Solid State Auto Switch (Refer to "Internal circuit" on page 11.) Wiring failure (2-wire type) 2 Satisfaction of the following relations by the load current specification. Load voltage is "ON" level The switch output doesnt turn off. The operation LED operates properly.
No.D-S-OMI0002-C PRODUCT NAME Solid state auto switch MODEL / Series / Product Number D-F6# Series Table of Contents Safety Instructions 2 Model Indication and How to Order 11 Summary of Product parts 11 Definition and terminology 12 Mounting and Installation 13 Installation 13 Circuit diagram 14 Troubleshooting 15 Specifications 19 Specifications 19 Dimensions 20 Operating range 21 -1No.D-S-OMI0002
Refer to SMC Compressed Air Cleaning System for the details of compressed air quality described above. 11 25 Piping ! Caution 1Preparation before piping. Thoroughly flush the fittings to prevent dust or chips from entering the gripper.
To verify the gripping condition or to make any adjustments, make sure to do so in an area where the air gripper or the workpiece will not fall. 11 - 3-2.
D-M9/ M9W/ Y59/ Y7P/ Y7W D-M9/ M9W/ Y59/ Y7P/ Y7W D-M9 D-M9V L (mm) D-M9 D-M9W D-M9V D-M9WV D-M9A D-M9AV MHY2-10D 3 1 5 3 MHY2-16D 3 1 5 3 MHY2-20D 3 1 MHY2-25D 1 ) 11 8. 1 2 ON ON 1 1),2)1 A 2 B 1),2) C 1 1 12 2) 3) 4) 0.30.5mm 2) 0.30.5mm 0.30.5mm 0.30.5mm 13 2-4. 1.
Connector and pin layout . 11 3-7. Center of gravity .12 4Product Specifications .13 4-1. Air gripper .13 4-2. 3-port solenoid valve .14 4-3. Auto switch .15 5. Operating method or operation .16 5-1Precautions for Design .16 5-2. Installation .16 5-3. CRX Plug-in software .20 5-4. Air supply .28 5-5. Piping .28 5-6. Operating environment .29 5-7. Lubrication .29 6.
Contact SMC sales representative in case of malfunction or maintenance. 11 - 3-8. Center of gravity The centre of gravity of the product is shown below. Adjust the position of the center of gravity with the robot controller. duAro Flange mounting surface X Y Z Center of gravity X Y Z 0.1 0.8 44.7 12 - 4. Product Specifications Warning 1.
Center of gravity Y Y Z X Flange mounting surface Z X Center of gravity X Y Z 2.4 0.0 42.6 11 4. Product Specifications * For detailed specifications not included in this document, please refer to our website (www.smcworld.com) or operation manual. 4-1.
Connector and pin layout . 11 3-7.Center of gravity . 12 4. Product Specifications. 13 4-1. Air Gripper . 13 4-2. 3 Port Solenoid Valve . 14 4-3. Auto switch . 15 5. Operating method or operation . 16 5-1. Precautions for Design . 16 5-2. Installation . 16 5-3. TMComponent . 20 5-4. Air supply . 24 5-5. Piping . 24 5-6. Operating environment . 24 5-7. Lubrication . 25 6.
M8 8 P .18 M8 8 () NPN PIN 1 +24V DC24V 2 3 4 5 ON/OFF 6 ON/OFF 7 8 GND DC0V M8 2 M8 1 11 - 3-7. Z Y Y X Z Z X X Y Z -0.4 -0.8 48.4 12 - 4 (www.smcworld.com) 4-1.
JMHZ2-16D-X7400B-HC10-(*) P13P14P15 4 M6 31.5 2XM4x0.7 8 4 M6 108.8L 4 4 M4 4 M3 27 17 10 - JMHZ2-16D-X7400B-HC10DT-(*) 4 M6 32.5 8 4 M6 109.8L 4 4 M4 4 M3 27 17 11 - 3-6. M8 8 M8-Molex P .19 NPN PNP No. 1 +24V DC24V 2 GND DC0V 3 ON/OFF() 4 ON/OFF() 5 () 6 () 7 8 Molex (51227-0800) M8 8 12 - 3-7.
Contact SMC sales representative in case of malfunction or maintenance. 11 - 3-8. Center of gravity The centre of gravity of the product is shown below. Adjust the position of the center of gravity with the robot controller. NEXTAGE mounting surface X Y Z Center of gravity X Y Z 0.18 0.03 46.06 12 - 4. Product Specifications Warning 1.
Electric shock can result. 11 - Install the electric actuator and its peripheral devices on a fire-proof material. Direct installation on or near a flammable material may cause a fire. Do not install the product in a place subject to vibrations and impacts. It will cause failure or malfunction.
Except during the pushing operation. 11) The maximum instantaneous power consumption (including the controller) is for when the electric actuator is operating.
How to Order 11 5. Structural Drawing and Replacement Parts 12 6. Operation and Adjustment 13-14 7. Trouble Shooting 15 8. How to Replace the Components 16-19 8-1. Diaphragm Assembly Replacement 16 8-2. Valve Guide Assembly and Valve Assembly Replacement 17 8-3. Square Embedded Type Pressure Gauge Replacement 18 8-4. Blanking Plate Assembly Replacement 19 9.
Therefore, be sure to follow the tightening torque. 11 4) Includes springs. 5) VXF26: If the customer ordered a product without a silencer and retrofitted the silencer, the operation at ON may become unstable. When retrofitting a silencer, it is necessary to replace the diaphragm assembly.
We do not guarantee against any damage if the product is used outside of the specification range. 11. Energizing for extended periods of time Caution hot surface Be aware that the valve surface may get hot. If a valve is continuously energized for an extended period of time, the temperature of the valve will increase due to the heat generated by the coil.
If this occurs, stabilize the ambient temperature and fluid temperature properly. -11- 6.
Drawings 11 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Implement measures to prevent any danger from occurring when operating the actuator. 11. Ventilation 2. Actuator drive When an actuator, such as a cylinder, is to be driven Provide ventilation when using a valve in a confined area, such as in a closed control panel.