FGX-OMZ0008 /12 FGX-OMZ0008 FGH Series / Specific Product Precautions Be sure to read this before handling.
A dual pressure supply can be supplied from both the left and right sides of the manifold. If 3 or more pressures are supplied, the individual SUP spacer should be used.
(In case of output OUT2, n_1, 2 to be n_3, 4 and P_1, 2 to be P_3, 4.)
If the valve is used with lubricated air, the factory pre-lubrication will be washed out so lubrication must be continued. 7. If lubricated air must be used, the external pilot type (VY1?01) and oilfree air supplied to the pilot port. 8. M a n i f o l d m o u n t e d v e r s i o n s o f t h e V YH y r e g a r e a v a i l a b l e .
B(9.5) B(12.7) B(19.1) 1B(25.4) 1 B(31.8) 1 B(38.1) 2B(50.8) VNA 111 211 311 411 511 611 711 AS 420-03 420-04 500-06 600-10 800-12 900-14 900-20 Caution Warning 1Piping When operation is suspended, surge pressure will be generated between the cylinder and VNA11A.
Electrical entry Symbol Specifications Configuration Body Ported Note) It cannot be mounted on a manifold.
Coil DC V100 Non-locking push type must be pressed in the direction of the arrow.
Equipment which may generate electromagnetic interference or whose function may be compromised by electromagnetic interference is required to be immune to electromagnetic affects (EMS/immunity) without emitting excessive electromagnetic affects (EMI/emission).
Standard Auto Switches Standard auto switches cannot be used under a strong magnetic field.
Equipment which may generate electromagnetic interference or whose function may be compromised by electromagnetic interference is required to be immune to electromagnetic affects (EMS/immunity) without emitting excessive electromagnetic affects (EMI/emission).
Can be switched from real-time flow rate to accumulated flow.
The mounting position of the pneumatic equipment needs to be considered. 4. Set the air flow capacity with an initial pressure drop of 0.03 MPa or less. If the initial pressure drop is set to be high, its service life will be shorten due to clogging. 5. Determine the product by the maximum consumption flow rate.
90 OC, but should be cared not to freeze.
VBA2A AMC510-06 270mm Mounting posture Horizontal VBA4A AMC610-10 300mm Handle-operated type Air-operat Handle-op Governor* * Separate piping should be prepared to If dry air (atmospheric pressure dew point 23C or less) is used, the ed type erated type life expectancy may be shortened because dry air will accelerate evaporation of grease inside.
Viscosities up to 1000 mPa s can be used.
The LVN series cannot be used as a stop valve. Be careful not to apply any excessive force to the stroke end, which fully opens and closes, to avoid accidental damage or changes in flow rate characteristics. 945
Mount the solenoid so that it will be on the same side as the single solenoid of the Series VZ3000. 2(A) port of 3 port valve should be 2(B) port of manifold base.
(Blocking discs will be placed between this station and the next one). 3) For identical stations in sequence, specity these at the same time. However, they must be in sequence to avoid confusion. The last specifcation for the assembly is the manifold base.
The cylinder ports are designed so that a maximum speed 3000 mm/s can be obtained. However, it may not be possible to attain the desired speed in the case of short cylinder strokes. It may also be impossible to attain the desired speed due to restriction by component equipment (valves, speed control valves, piping, fitting, etc.).
(Blocking discs will be placed between this station and the next one). 3) For identical stations in sequence, specity these at the same time. However, they must be in sequence to avoid confusion. The last specifcation for the assembly is the manifold base.