Soft Start-up Valve Do not use in an atmosphere where corrosive gases, chemicals, sea water, water, or water vapor is present. Do not use in cases where there is direct contact with any of the above. 2. Do not use in an explosive environment. 3. Do not use in a place subject to heavy vibration and/or impact. 4. The valve should not be exposed to prolonged sunlight. Use a protective cover if necessary. 5.
In such cases, it is recommended to use a dual speed controller. 3) Do not scratch or gouge the sliding portion of the piston rod and the guide rod. Damaged seals etc. will result in leakage or malfunction. 4) Do not dent or scratch the mounting surface of the body and the plate.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not use in an atmosphere where corrosive gases, chemicals, sea water, water, or water vapor is present. Do not use in cases where there is direct contact with any of the above. 2. Do not use in an explosive environment. 3. Do not use in a place subject to heavy vibration and/or impact. 4. The valve should not be exposed to prolonged sunlight. Use a protective cover if necessary. 5.
Solmldc.pc y indud6 cap, (1)rutbre3 pluo dor 15, (r ) dr 19, (2) (h 13, (2) dn 14, dnd (1) d.r 7 sc@01 t2B sordrdrdcp*3y. t'dud6p, (r) rss$d i@roddng cp...ro.dor t6. 0 ) &l 1q (2) del 13, (2) d.l 14, -d 11 | d.r 7lv5tv rvd'l{1 s6602 Solmidc4 s y. hdude, (1) .ubod a@ds plus rb| r 5, (1) irdi@ro.lign a$nbry dor 1 7& 13, (1 )drr 19, (2) dr 13, 12) d6r 14. and lrl dat 7 (b,vo lve 1"1 1 6 sdendd
D and DO type DC specifications are 24VDC or 12VDC only. D and DO type are for SY5000/7000 only.
Do not use in a location having an explosive atmosphere. 2. Do not operate in locations where vibration or impact occurs. 3. Do not use in locations where radiated heat will be received from nearby heat sources. Maintenance Warning 1. Maintenance should be performed in accordance with the procedures in the Operation Manual.
Do not apply negative pressure. It may result in malfunction. Should they remain, they could cause malfunction. 3. When connecting pipes and fittings, etc., be sure 3. Do not supply air pressure from ports other than that neither chips from the pipe threads nor sealing material get inside the valve.
Do not twist the valve seal 1.
Do not use in explosive atmospheres. 2. Do not use in locations subject to excessive vibration or impact. Impact resistance of this solenoid valve is 150 m/s2. Vibration resistance of this solenoid valve is 30 m/s2. 3. Do not use in locations where radiated heat will be received from nearby heat sources.
Do not twist the valve seal 1.
Unused Lead wire assy U side 6 stations (14 stations) Pin Confirm an insertion of the lead wire assembly after the insertion of pin by light pulling of the lead wire. (n) 4. Mount the end plate !2 and !3 and tighten the bolt !1. 7 stations (15 stations) (2) (1) Stations Note 1) Be careful that the packing and the O-ring do not fall out of the groove.
Hexagon wrench (Width across flats 4mm) 13 14 Spanner (Width across flats 13mm) Fig.1 13 Open Close Fig.2 10 XL-OMP0001 6.
EO 14 16 20 NB 5h9 6h9 6h9 DC 30 36 42 NA 8 10 12 DO 34 40 48 K 4 5 6 B 30 36 42 Q 6 7 8 J 10 12 14 AA 35 38 40 AB 32 35 37 O 2 2.5 3 P M3 x 0.5 M5 x 0.8 M5 x 0.8 0 -0.030 0 -0.030 0 -0.030 Model MHS2-16D MHS2-20D MHS2-25D VA 2H9 2H9 3H9 TB 5 6 6 SC 8 9.5 10 RB 16 18 22 RA 18 24 26 WA VB 2 2 3 XA 2H9 2H9 3H9 XB 2 2 3 +0.025 0 +0.025 0 +0.025 0 +0.043 0 +0.052 0 +0.052 0 +0.025 0 +0.025 0
Piping Caution Caution Handling 1.Do not inadvertently move the guide adjusting unit. The guide is installed at the proper tightening torque. Do not loosen the mounting bolts of the guide. 2.Do not operate the magnetic rodless cylinder if the magnet couplings on the actuator are displaced.
Do not use valves in atmospheres of corrosive gases, chemicals, salt water, water or steam, or where there is direct contact with same. 2. Do not use in an explosive atmosphere. 3. Do not use in locations subject to vibration or impact. 4. Do not use in a location where radiated heat will be received from a heat source in the vicinity. 5.
Do not connect black. Power supply/output connection lead wire Cable Specifications Pin no.
Do not use the auto drain valve in such environment.
S 24 M5 x 0.8 (Finger closing port) 42 8 3 4 3 MHY2-25D2 Opening/Closing direction through-hole type 4-5.5 (Hole for mounting attachment) 12 0.005 0.025 6 12 22.5 (Limted area for mounting attachment) Do not extend the attachment from limited area for mounting to avoid interference with the attachment or main body. 12-10-14 14 180 Angular Style Air Gripper Cam Style Series MHY2 Mounting
S 24 M5 x 0.8 (Finger closing port) 42 8 3 4 3 MHY2-25D2 Opening/Closing direction through-hole type 4-5.5 (Hole for mounting attachment) 12 0.005 0.025 6 12 22.5 (Limted area for mounting attachment) Do not extend the attachment from limited area for mounting to avoid interference with the attachment or main body. 12-10-14 14 180 Angular Style Air Gripper Cam Style Series MHY2 Mounting