KJ Has large retaining force while holding force is increased by the collet.
Return to the origin position can be done by the [RTN ORIG] button. -27JXC-OMU0010-A 5.4 Teaching method Teaching is a method to set a position by operating the actuator. Teaching method has Jog teaching and Direct teaching. Caution The actuator is operated during teaching.
(Refer to page 56) Level meter: Displays the measured distance (reference) by figure. Display value: Displays the measured distance (reference) by value.
The PB1011A transfers the fluid continuously by suction and discharge in turn by repeating ON/OFF of the built-in solenoid valve. The PB1013A air-operated type is operated by the ON/OFF operation of an external solenoid valve.
a spring force, which is further tilted by the load that is applied to the cylinder, thus locking the piston rod.
the following formula that is based on the test conducted by the test circuit analogous to ISO 6358.
Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires. This may not only cause broken lead wires, but it may cause internal elements of the switch to be damaged by the stress. 3. Mount switches using the proper tightening torque. If a switch is tightened beyond the range of tightening torque, the mounting screws or switch may be damaged.
Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires. This may not only cause broken lead wires, but it may cause internal elements of the switch to be damaged by the stress. 3. Mount switches using the proper tightening torque. When a switch is tightened beyond the range of fastening torque, the mounting screws or switch may be damaged.
Wireless master
Air supply The compressed air supplied to the cylinder should be filtered by SMC AF series air filter and regulated to the specified set pressure by SMC AR series regulator. Warning 1.Use clean air.
Tighten the lock nut on cable side by turning it clockwise by hand. Aligning the key groove with the IN-side communication connector ( 5-pin, plug ) of GW unit, plug the PROFIBUS DP communication cable ( socket ). Confirm that the connector portion does not move.
With by-pass A small amount of fluid from the inlet side is allowed to flow continuously to the outlet side by providing a by-pass inside the body. Adjustment knob Adjusts the flow rate. Lock nut Locks the adjustment knob position. Adjustment handle Adjusts the flow rate.
Use ihte type when instrtttng t2mm or closer to th neareat sensor, separato by at least zmm when using three or more sensots.
With reduced mounting height and overall length, Low profile Low profile Compact body Compact body Lightweight Lightweight Overall length reduced by 31% Overall length reduced by 31% Weight reduced by 50% Height reduced by 29% Overall length reduced by 31% Weight reduced by 50% Weight reduced by 50% Height reduced by 29% Height reduced by 29% CY1F kg 10 15 25 Series MX CY1F CY1H MY2H 0.7
the 1 mm stroke interval. 40 to 100: Available by the 5 mm stroke interval.
With reduced mounting height and overall length, Low profile Low profile Compact body Compact body Lightweight Lightweight Overall length reduced by 31% Overall length reduced by 31% Weight reduced by 50% Height reduced by 29% Overall length reduced by 31% Weight reduced by 50% Weight reduced by 50% Height reduced by 29% Height reduced by 29% CY1F kg 15 25 10 Series MX CY1F CY1H MY2H 0.7
Long range static neutralization and dust removal Offset voltage: Within 10 V* Increases air blow flow rate by external air intake Ionized air assisted by the compressed air Improved dust removal performance by the energy of compressed air. Suitable for static neutralization at a long distance (max. 500 mm). Static neutralization is possible with minimal air consumption.
Intermediate strokes Spacer installation type Spacers are installed in the standard stroke cylinder. 12 to32: Available by the 1 mm stroke interval. 40 to63: Available by the 5 mm stroke interval. Description Model no.
The lock ring is tilted by the brake spring force. 2. The tilting is increased by the load and the piston rod is securely locked. Unlocking port: Air supplied 1. The lock ring becomes perpendicular to the piston, creating clearance between the piston rod and lock ring, which allows the piston rod to move freely.
Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires. This may not only cause broken lead wires, but it may cause internal elements of the switch to be damaged by the stress. 3. Mount switches using the proper tightening torque.