IZx-OMX0087 an alternative location for the ionizer.
30 20 10 Transfer speed V m/min Transfer speed V m/min Allowable lateral load MIW20 MIS20 MIW12 MIS12 200 0.2MPa 0.3MPa 0.4MPa 0.5MPa 0.6MPa 0.7MPa 70 180 0.2MPa 0.3MPa 0.4MPa 0.5MPa 0.6MPa 0.7MPa 60 160 50 140 Lateral load N 40 120 Lateral load N Point of application L 30 100 20 80 Lateral load F 10 60 40 80 70 60 50 40 30 30 20 Point of application L mm 80 60 40 120 100 Point of application
In an environment where vibration or impact occurs, provide an intermediate support even if the distance is within the allowable range in the graph. W L In case the product is installed on the ceiling, regard the mounting bolt pitch as L.
An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Do not operate in an atmosphere containing flammable, explosive or corrosive gas. Fire or an explosion can result.
105 M30 X 1.5 30 39 69.5 4 CM2 86.5 5 4 X 40 40 32 28 8 60 55 110 M36 X 1.5 34 39 76.5 4 94.5 5 4 X 40 50 40 32 8 67 70 125 M40 X 1.5 44 42.5 84.5 4 C85 180/200 250 300 5 4 X 55 115 50 40 8 67 70 125 M45 X 1.5 44 40 42.5 105 4 6 5 X 65 144 9 86 160 66 63 75.5 M56 X 2 53 50 132 50 5 CG1 6 5 X 80 178 9 175 71 84.5 M64 X 2 66 105 166 80 63 63 5 Y type double knuckle joint Rod end nut MB C95
This feature is useful when an output to check the rod position at intermediate stroke is required. No.
An injury or failure can result. Caution 1. Pay attention to the length of time that a switch is ON at an intermediate stroke position. When an auto switch is placed at an intermediate position of the stroke and a load is driven at the time the piston passes, the auto switch will operate, but the operating time will be short if the speed is too fast.
8 12 24 5 10 5 10 Vertical 32 10 12 10 20 10 12 10 20 40 High rigidity direct acting guide LJ1H 20 20 40 44 Horizontal 50 25 25 60 Non-standard motor 8 12 8 12 66 5 10 5 10 Vertical 74 10 10 82 Options Page 100 Made to Order 101 Clean room specification 104 Dust seal specification 110 TSUBAKI CABLEVEYOR specification 122 Construction 134 Mounting 140 Non-standard Motor Mounting
Result of endurance test (with the circuit shown on the right) The valve was opened and closed in an internal vacuum state at an ordinary (room)temperature and checked for internal and external leakage and operation.It was confirmed that XLA-16, XLA-25, XLA-40, XLA-50, XLA-63 and XLA-80 satisfied the product specification up to 2 million cycles, XLA-100 and XLA-160 did up to 1 million cycles
Replacement Procedure is P.437 Construction AWG20 AWG30/40 Actuators Modular F.R.L.
Replacement Procedure is P.437 Construction AWG20 AWG30/40 Actuators Modular F.R.L.
Tightening Torque for Stroke Adjustment Unit Holding Bolts Unit: Nm Bore size (mm) 25 32 40 Tightening torque End lock 1.8 3.5 Operating direction 5.8 L R Caution R L R L R L R L Do not operate with the stroke adjustment unit fixed in an intermediate position.
1 Platform Cylinder Series CXT 12, 16, 20, 25, 32, 40 A highly rigid and highly accurate slide table integrated with an actuator. MX MTS Two styles of guide rod bearings to accommodate your application Slide bearing For heavy loads Ball bushing bearing For highly accurate and smooth operation MY CY Auto switch can be mounted.
Caution When using an exhaust cleaner, mount it downwards.
40 1.5 1 1.5 1 K K 3 3 3 3 5 5 5 5 (mm) LECP6 LECP6 ( NPN NPN 32 16 16 32 10 10 PNP PNP 48 20 24 20 24 48 LECP1 1 LECP1 ( 1 NPN NPN 64 32 32 32 32 64 PNP PNP 1P 1P 80 40 40 40 40 80 AN LECPA ( AN LECPA NPN NPN AP AP PNP PNP (m) () 8 8 8 8 L L 1.5 1 1.5 1 A A 10 10 3 3 3 3 B B 15 15 5 5 5 C C 20 20 5 () () R R S S / P.42 7.3 <> (NPNPNP) LEHF10K2-16 3 - 3.3 9 13 16
System configuration Be sure to secure an air supply capacity of the minimum operating pressure (0.1 MPa) or more.
An application which could have negative effects on people, property, or animals requiring special safety analysis. 4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical protective function, and periodical checks to confirm proper operation.
If excessive kinetic energy is expected, install an external absorber to prevent impact to the body of the product. In this case, please verify the rigidity of the equipment carefully. 40 50 63 80 100 Table 1 Air cushion 2.8 4.6 7.8 16 29 Allowable kinetic energyJ Non cushion 0.33 0.56 0.91 1.50 2.68 9 2-7.
Precautions Pull a connector out vertically, never at an angle.
Precautions Pull a connector out vertically, never at an angle.