Cooling Capacity: 28 kW, Thread: Rc, Option: w/Caster Adjuster-foot
Cooling Capacity: 100 (10.5kW), Thread: Rc, Option: A (w/Caster Adjuster-foot)
Cooling Capacity: 200 (20.5kW), Thread: Rc, Option: A (w/Caster Adjuster-foot)
Cooling Capacity: 300 (28 kW), Thread: Rc, Option: A (w/Caster Adjuster-foot)
Cooling Capacity: 250 (25kW), Thread: Rc, Option: A (w/Caster Adjuster-foot)
AMF If these items need to be supported, provide an additional support. t A Class 2 Pressure Vessel Pressure Resistance Certificate is provided with those below, which are considered to be Class 2 pressure vessels. Make sure to store the certificate in a safe location.
Use caution, as there is a danger of being burned if a valve is touched directly. 2. Valves may reach high temperatures when continuously energized. Use caution, as there is a danger of being burned if a valve is touched directly. SOL. AC AC SOL. Without light AC SOL.
The maximum protrusion of an auto switch (when fingers are fully closed) from the edge of the body is shown in the table below. Use the table as a guideline for mounting. Auto switch mounting bracket part no. BMG2-012 Auto switch part no. D-M9(V)/M9W(V)/M9A(V) Note) Use a screwdriver with a grip diameter of 5 to 6 mm to tighten the set screws (M2.5).
140.5 LVR50-V19 22 80 120 169 C F E Breathing port M5 x 0.8 J Tube extensions 4 x 7 Mounting hole 1/8 (Rc, NPT) Pilot port A H D B G Breathing port M5 x 0.8 Model A B C D E LVR20-T07(06) 40 40 49.3 68 20.1 LVR40-T11(10) 82.5 82.5 89 115 33 IN C F Model F G H J K LVR20-T07(06) 8 27 56 33.5 126.2 LVR40-T11(10) 14 64.5 100 40 183.3 E K J J Breathing port M5 x 0.8 5 Applicable Fluids Regulator
Manifold Options JIS symbol Blanking plate assembly VVCW 0 3A 2 A Series Material 2 3 4 Class 2 Class 3 Class 4 Plate material C37 Stainless steel Seal material Symbol A H FKM This is used by mounting it on the manifold block when a valve is removed for maintenance, or when the mounting of an additional valve is planned, 5 Series VCL Direct Operated 2 Port for Oil Dimensions (mm) (N.C.)
The life of a buffer will be reduced if the lateral force is applied to the buffer shaft. Note that sometimes a load is applied to the buffer by a piping tube (pulling or pressing, etc. in a lateral direction). 5. Do not apply an impact or large forces to a pad when adsorbing a workpiece. This will cause deformation, cracking and wear of the pad to be accelerated.
Conforming to ISO 16030-2001, the chamfered dimensions shown in the First, tighten it by hand, then give it an additional 1/6 turn to 1/4 turn with a wrench. A reference value for the tightening torque is 1 to 1.5 Nm. Note) Excessive tightening may damage the thread portion or deform the gasket and cause air leakage. table below are recommended.
Conforming to ISO 16030-2001, the chamfered dimensions shown in the First, tighten it by hand, then give it an additional 1/6 turn to 1/4 turn with a wrench. A reference value for the tightening torque is 1 to 1.5 Nm. Note) Excessive tightening may damage the thread portion or deform the gasket and cause air leakage. table below are recommended.
(With gasket, 2 mounting screws) VC VDW VQ Blanking block assembly (VCA30, 40) VVCA 3 0 2A 00 VX2 VX Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com 3 4 Series VCA30 Series VCA40 VX3 This is used when a blanking plate is mounted on a manifold as preparation for a
water flow of 4l/min at a differential pressure of 0.1MPa, an effective area with Cv factor 0.28 (VDW303) or more is required.
Note 2) The grommet type is equipped with a surge voltage suppressor (direct coupling type lead wire), but not an indicator light.
x 1.25 M10 x 1.5 185 145 95 80 50 40 25 26 M39 x 1.5 40 Note) The pin, keeper plate and cap bolt are included with a double knuckle joint.
Micro-Mist Separator Regulator AWD20/30/40 Series AWD is a component made up of a regulator and a micro-mist separator that are integrated to provide optimum results in applications such as ultraclean air blow operations.
Plate A Plug (M-3P) (2 pcs.) Plate B (with O-ring) Tighten by hand and give it an additional turn approx. 1/4 rotations with a wrench.
Model A B C A B C A B C A B C 500 1000 1500 1000 2200 3000 2000 3300 4000 4000 5700 7000 34.5 38 40 33 36.5 38 34 36 37 34 35 36 35 40 44 35.5 40 42 37 40 41.5 38 40 42 35.5 42.5 47.5 36 42.5 44 38.5 42.5 45 39 43 45 HAA7 HAA15 HAA22 Maintenance HAA37 Caution 1. Inspect the cooler at least once a week and clean it to prevent it from becoming obstructed. 2.