CY1 Do not use a load that generates surge voltage.
Proper auto switch mounting positions (Series CE1) (mm) Bore size (mm) Auto switch model Symbol 20 32 40 50 63 12 A B A B A B A B A B A B A B A B A B 40.5 47 55 79 82 85.5 D-A7, A8 4 13 17 39 44 41.5 Contact protection box internal circuits 41 47.5 55.5 79.5 82.5 86 D-A7H, A80H, A73C, A80C, D-F7, J79, F7V, J79C 4.5 13.5 17.5 39.5 44.5 42 Choke coil OUT Brown [Red] CD-P11 38 44.5 52.5 76.5
Operating principle A + A' A' A Piston seal A' A' R H R H When the piston is retracting, air is exhausted through both A and A' until piston seal H passes air passage A. After piston seal H has passed air passage A, air is exhausted only through A'. The section marked with slanted lines becomes a cushion chamber, and an air cushion effect is achieved.
When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
Installation at indoor site 1 In case of facility having a large installation area (that can vent the air naturally) Make an air outlet on a wall at a high level and air inlet on a wall at a low level, to allow for adequate airflow. 2 In case of facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air
For a facility having a large installation area (that can vent the air naturally): Make an air outlet on a wall at a high level and air inlet on a wall at a low level, to allow for adequate airflow. 2. For a facility having a small installation area (that can not vent the air naturally): Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level.
failsafe system is a system that remains in the safe state or immediately enters a safe state when specific failures occur. i-Parameter Individual safety parameters of a module OSSD An Output Signal Switching Device is a safety related output of a sensor that are self-checked.
GC SB + Stroke B ZZ + Stroke A + Stroke B SA + Stroke A 63 SZ + Stroke B Front mounting flange C port A, B port B port A 20 C port A port A ' View A-A' GC SB + Stroke B ZZ + Stroke A + Stroke B SA + Stroke A 41 Made to Order Specifications Series MGG Auto Switch Rail Mounting 8 MGG XC13 Bearing type Mounting type Stroke Auto switch type Auto switch symbol Bore size Auto switch rail mounting
flow rate of 14.1 scfm [400 L/min] (ANR) is P1 29 psi (0.2 MPa) for a 4 orifice and P1 84 psi (0.58 MP)a for a 3 orifice.
Single vane Double vane 90, 100D 270S 180S 90S 0 5o g e n a 2 0o r 7 +4o 0 n +4o o o g n e o 0 a ti r 1 0 0 8 0 n a 9 0 o 1 +4o o t ti +4o e o a 0 g e t R n 0 o g a R o r n 0 n 9 ra o ti e a n g t io o n R at a r ot n R o (90o) (90o) ti a t o R Chamfer Chamfer (45o) Chamfer (45o) B port Chamfer A port B port A port B port (40o) B port A port A port For size 40 actuators, a parallel key will
When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
x 20 /C1 7 x 45o 7 x 45o 22.5o 22.5o A A A A 166p0.2 178p0.2 A-A A-A The surface roughness of the orifice machining should be Rz6.3 or less.
Installation at indoor site 1 In case of facility having a large installation area (that can vent the air naturally) Make an air outlet on a wall at a high level and air inlet on a wall at a low level, to allow for adequate airflow. 2 In case of facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air
: A12 Symbol: A13 Symbol: A14 Symbol: A15 R sphere C0.5 DA DA AL MM DA C C DA 30 30 30 H A A H H A H W1 T C Symbol: A16 Symbol: A17 Symbol: A18 Symbol: A19 MM AL DA MM 30 30 30 30 MM MM H A H A H A C H A 46 CP96N/C96N Series Symbol Change of Rod End Shape 1 -XA0 to XA30 Symbol: A20 Symbol: A21 Symbol: A22 Symbol: A23 RD 30 30 MM 30 DA MM 30 DA MM L DB DB C H A T H A T H A B W H A L K Symbol
When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
Type S31 Manifold: Side Ported 91.7 [96.1] Approx. 300 (Lead wire length) SS5YJ3-S31Stations -M3 L1 L2 3.5 2-3.5 (For mounting) Manual override M5 x 0.8 (P, R port) 5.2 29.2 7.5 52.2 [54.4] 51.4 [53.6] 17.3 30 3 91.7 [96.1] 78.8 [83.2] 78.8 [83.2] 13.5 A A A A A B B B B B P R P R P R 29.2 P R 30 17.3 25 7.5 12 25 51.4 [53.6] 52.2 [54.4] 13.5 B B B B B A A A A A 3 5.2 2-3.5 (For mounting)
When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
When a load, such as a relay or solenoid valve, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.