CRBB-OM00004 1 2 Holding block (A) 1 2 1 Switch block (A) 1 1 Switch block (B) 1 1 Holding block (A) 1 No.
A CAT.ES100-43 A For General Fluids High Precision Digital Pressure Switch F/ISE ZSE 50 60 50 60 Series High precision/High resolution pressure switch. Applicable for pressure detection with a wide range of fluids, by using a stainless steel diaphragm. Pressure detection for a wide range of fluids.
Auto drain product number for replacement bowl assembly Product number Product name QTY remarks AD48N-Z-A(Thread Symbol N) bowl assembly With bowl packing AD48-A(Thread Symbol None) bowl assembly With bowl packing C42FP-260S bowl packing 111692 strainer Note 1) strainer is not included in bowl assembly.
A model should be selected with a gripping force of 7 to 14 times that of the workpiece mass. If high acceleration, deceleration or impact forces are encountered during motion, a further margin of safety should be considered.
Insert a hexagon wrench from the bottom of the pad, loosen the screw and remove the old pad from the adapter. 2. Place a new pad on the adapter, and after confirming that the O-ring is in place, retighten the screw with the hexagon wrench. Adapter z Pad O-ring on inside x Hexagon wrench Pad diameter: 40, 50 1.
P = 43 PA 23 A A B B 14 12 A PA PA L1 L2 L2 L1 B B B 14 12 A A A A B 14 A A PA B B (2n 1/8) 4n-1/4, 3/8 2, 4 port PA L-side R-side L-side R-side D-side D-side 89 3 89 16 141 (Single) 141 (Single) 55 44 186 (Double) 186 (Double) 196 (3 position) 196 (3 position) 77.5 Bottom ported M12 connector L: Dimensions n: Stations 141.5 L n 1 Formula 2 3 4 5 6 7 8 9 10 121 5 1 12 14 PA PB 107 L1 = 43n
When the cylinder is used with a clamping mechanism, there is a danger of work pieces dropping out of it if there is a decrease in clamping force due to a drop in circuit pressure caused by a power outage. Therefore, safety equipment should be installed to prevent damage to machinery and human injury.
See abnormal values at a glance. See abnormal values at a glance. Push Push Adjust to the set-value by the or button.
D 8 I m + mL kgm Find the gripper's moment of inertia. b a+b 12 I = m + mL kgm a Find the actual moment of inertia.
Y B G A 90 B 90 B G A D Note 1) 90 G A H X X X D Note 1) D Note 1) B B B F E F F E A H A G G RG RT RS B 296 305 C R310 R445 D 93 129 E 60 87 F 10 15 G 6 7 B 296 309 C R390 R495 D 93 129 E 60 87 F 10 15 G 6 7 B 299 307 C R350 R440 D 93 129 F 10 15 G 6 7 H 610 700 A 600 743 A 680 797 A 643 740 15 32 15 32 15 32 Y Note 2) Y Note 2) Y Note 2) X 558 to 573 685 to 708 X 518 to 533 558 to 581 X
Insert a hexagon wrench from the bottom of the pad, loosen the screw and remove the old pad from the adapter. Adapter z 2. Place a new pad on the adapter, and after confirming that the O-ring is in place, retighten the screw with the hexagon wrench. Pad O-ring inside x Hexagon wrench Pad diameter: 40, 50 1.
Use a soft cloth to remove stains.
If a resin tubing is used for piping under these circumstances, the tubing might get softened and exploded. Therefore, be sure to cool the facility water over time and flow the facility water with a proper flow rate. T U V . Z A B . (M5:3.0Nm, M6:5.2Nm) Jan o To Uo Vo . Zo Ao Bo . Internal sensor value for alarm = Internal sensor value Fine control value 5.4 Piping Feb P TP UP VP .
When a surge generating load such as a relay or solenoid is directly driven, use a type of switch with a built-in surge absorbing element. 4. Since the type of applicable fluid varies depending on the product, be sure to verify the specifications. The switches do not have an explosion proof rating. To prevent a possible fire hazard, do not use with flammable gases or fluids. 5.
If installing a tank externally, only a sealed tank should be used. Do not use an open tank. Sep W TW UW VW . ZW AW BW . Oct X TX UX VX . ZX AX BX . Nov y Ty Uy Vy . Zy Ay By . Normal When high head pump option selected Dec Z Tz UZ VZ .
Blanking block assembly (VCA30, 40) VVCA 3 0 2A 00 3 4 Series VCA30 Series VCA40 This is used when a blanking block is mounted on a manifold as preparation for a planned valve installation.
Next, IB is entered to find IA the moment of inertia for the rotation of shaft (A) as a + b 2 2 A = ( ) b a 2 B = m 12 No. of teeth = b 11-10-3 4 Technical Data 3: Theoretical Output 5.
Use caution, as there is a danger of being burned if a valve is touched directly. 2. Valves may reach high temperatures when continuously energized. Use caution, as there is a danger of being burned if a valve is touched directly. SOL. AC AC SOL. Without light AC SOL.