CE Note) Do not apply rotational torque to the piston rod. When the stroke reading cylinder is used near a motor, welding machine or other source of noise generation, there is a possibility of miscounting. In this case, noise should be suppressed as much as possible and the following countermeasure should be taken. 1. Connect the shield wire to FG (flame ground). 2.
Do not use it in such a way that a load could be applied to the piston rod during the retraction. The spring that is built into the cylinder provides only enough force to retract the piston rod. Thus, if a load is applied, the piston rod will not be able to retract to the end of the stroke.
Do not add the suffix (N) indicating no lead wire to the part numbers of models D-A3A, A44A. G39A and K39A. Lead wire length symbols: 0.5 m Nil (Example) C73C 3 m L (Example) C73CL 5 m Z (Example) C73CZ None N (Example) C73CN In addition to the models in the above table, there are some other auto switches that are applicable.
Load Load (a) (b) Thrust bearing Flexible coupling Bearing Size Allowable thrust load (N) Allowable radial load (N) (a) (b) 10 15 20 30 40 7.8 15.7 14.7 9.8 19.6 19.6 29.4 49 49 49 98 78 59 108 98 MSQX Do not allow the load and moment applied to the table to exceed the allowable values shown in the table below.
Model Pressure range *1 Indication unit Connection thread Note MPa Port size 01 Rc1/8 02 Rc1/4 R1/8 R1/4 G46-7-02-SRB 0 to 0.7 R1/4 G46-10-02-SRB 0 to 1.0 G46-4-01 to 02-SRB 0 to 0.4 MPa Set pressure range: 0.05 to 0.69 MPa 02 WR110 X215 *1: Do not apply more pressure than the max. pressure displayed. It may cause a malfunction.
(Do not use any tools.) The initial exhaust rate is adjusted by turning the adjustment nut counterclockwise.
To prevent this, do not set the supply pressure higher than necessary. Soft workpiece Workpiece that has concave/convex surfaces As soft workpieces are easy to deform, there is a tendency for the workpiece to touch the bottom of the non-contact gripper. Please be aware that the workpiece may touch the gripper before using.
Do not tighten the initial air supply flow any further than the minimum supply flow position, as this may result in component damage, or in increased time needed to attain a vacuum in the vacuum chamber due to a decline in the displacement capabilities of the gas accumulation part (bellows chamber). 1.
Do not service or attempt to remove product and machinery/ equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.
Do not replace the bushings. The bushings are press-fit. To replace them, they must be replaced together with the cover assembly. 2. To replace a seal, apply grease to the new seal before installing it. If the cylinder is put into operation without applying grease to the seal, it could cause the seal to wear significantly, leading to premature air leakage. 3.
Do not replace the bushings. The bushings are press-fit. To replace them, they must be replaced together with the cover assembly. 2. To replace a seal, apply grease to the new seal before installing it. If the cylinder is put into operation without applying grease to the seal, it could cause the seal to wear significantly, leading to premature air leakage. 3.
Do not replace the bushings. The bushings are press-fit. To replace them, they must be replaced together with the cover assembly. 2. To replace a seal, apply grease to the new seal before installing it. If the cylinder is put into operation without applying grease to the seal, it could cause the seal to wear significantly, leading to premature air leakage. 3.
Do not replace the bushings. The bushings are press-fit. To replace them, they must be replaced together with the cover assembly. 2. To replace a seal, apply grease to the new seal before installing it. If the cylinder is put into operation without applying grease to the seal, it could cause the seal to wear significantly, leading to premature air leakage. 3.
/set) do not include a grease pack (10 g), order it separately. Grease pack part no.: GR-S-005 (5 g) 7
Do not use a stop valve to prevent damage to the differential pressure gauge if the valve is inadvertently left open or closed. 2) Install the differential pressure gauge vertically. 3) The piping of the differential pressure gauge must be connected securely because it will break if it becomes detached. 1.
Do not allow the weight of piping to lie directly on air dryer. Operating Environment Caution The air that has been used for reactivating the adsorption agent and the air that has passed through the indicator are discharged externally from the heatless air dryer. Therefore, use the dryer in an area where the discharge will not be a problem.
Note) Do not apply rotational torque to the piston rod. When the stroke reading cylinder is used near a motor, welding machine or other source of noise generation, there is a possibility of miscounting. In this case, noise should be suppressed as much as possible and the following countermeasure should be taken. 1. Connect the shield wire to FG (flame ground). 2.
Do not add the suffix (N) indicating no lead wire to the part numbers of models D-A3A, A44A. G39A and K39A. Lead wire length symbols: 0.5 m Nil (Example) C73C 3 m L (Example) C73CL 5 m Z (Example) C73CZ None N (Example) C73CN In addition to the models in the above table, there are some other auto switches that are applicable.
.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com Lead wire length indication D-A9/A9V The above auto switches do not have internal contact protection circuit. 1. Operating load is an inductive load. 2. The length of wiring to the load is 5 m or more. 3. The load voltage is 100 VAC.
Screw the locking ring into the switch (do not tighten with pliers, hand tishten only). Lead Wire with Connector Length 0.5 m 3 m 5 m Part no.