HRX-OM-R016 Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.
Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.
Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.
ARP VY1D00 VY1400 IR-A Simple circuit configuration IR 1 Piping labor reduced A flexible system has been adopted.
A set of side supports consists of a left support and a right support. 1352 MY1W Series Mechanically Jointed Rodless Cylinder With Protective Cover Construction MY1W o !6 !3 !1 u t q w e y !2 i r #3 !4 !0 !9 !8 !5 !
FGDT/F(L250) Replacement case assembly FGDT/F(L500) FGDC/E(L250) FGDC/E(L500) 25 A FGD Series Dimensions FGDA (1 element) FGDB (2 elements) 108 108 2 x Rc 2 x Rc AIR VENT M6 AIR VENT M6 OUT IN OUT IN B A FGDT FGDF B A DRAIN DRAIN G1/4 G1/4 Element removal dimension: 50 mm (mm) A B Model Element length Port size Rc 314 346 A (L250) FGDC FGDE 574 606 B (L500) 3/8, 1/2, 3/4 314 349 A (L250)
C a u t i o n Use a specific mounting bracket (Table 2) and mount the product so that the band of the bracket will be perpendicular to the stroke of the product. Tighten mounting screws to the appropriate torque. The auto switch can only be used for cylinders with a built-in magnet for auto switch (e.g. CDM2).
U Function to change the unit in which the value of pressure is indicated. Only a product with this function can change the unit. A product with unit-changing function cannot be purchased if it is used within Japan. Pressure is indicated only by SI units in Japan. Unit selection function W A measure of the products resistance to a voltage applied between the electrical circuit and case.
Avoid using in a place that exceeds an ambient temperature range. b. Avoid using in a place that exceeds an ambient humidity range. c. Avoid using in a place where condensation occurs due to a drastic temperature change. d. Avoid using in a place in the presence of corrosive or explosive gas or where there is a volatile combustible. e.
Check if the load is short circuited. (3) Check if a relay without a surge (3) Use a relay with a surge voltage suppressor or take measures to prevent noise.
U Function to change the unit in which the value of pressure is indicated. Only a product with this function can change the unit. A product with unit-changing function cannot be purchased if it is used within Japan. Pressure is indicated only by SI units in Japan. Unit selection function W A measure of the products resistance to a voltage applied between the electrical circuit and case.
2(A) 47.5 VHS 13.5 (A port) Rc 3/8 Individual exhaust: VV3PA5-42Station 3-03 28.5 3(R) 3(R) (R port) Rc 3/8 PA NO NC 87 (PA port) Rc 1/8 (Mounting hole) 2-7.2 30 PA 41.5 91.4 84.4 91.4 60 16.5 1(P) 41.5 PA (P port) Rc 3/8 (Pitch) 88 31 33 7.5 L2 L1 (PA port) Rc 1/8 PA 61.5 66 2(A) 2(A) 47.5 13.5 (A port) Rc 3/8 n: Station n L L1 L2 Formula L1 = 33 x n + 29 L2 = 33 x n + 14 6 227 212 7 260
1/2(15 A) 3/4(20 A) 1(25 A) Weight(Body) *5 Approx.
Dont use a wrench on push-to-connect end. 2 2 Cut tubing square with a clean 90 edge Dont use excessive tube angle cut which can lead to leakage or breaking. 90 90 3 3 Use SMC Tube Cutters Dont use dikes, a knife, a saw or a dull tool to cut the tubing.
It results in generation of a play, increase sliding resistance or air leakage. Consult P/A for in case of usage in such an environment. 3.Install a shade screen if exposed to the direct sun light. 4.Install a blocking cover if a heat source is in the area.
MY-SA 2 x G F 2 x H E C D A B Side support B MY-SB 2 x J MY1B MY1B MY1H E A B MY1B C D MY1M (mm) MY1C A 61 70 87 B C D E F G H J Part no.
+ A = 100 y, z + A 100 10 y, z + A = 200 y, z + A = 200 y, z + A = 300 y, z + A = 300 1 1 0 200 400 600 800 1000 1200 0 100 200 300 400 500 600 700 800 Stroke [mm] Stroke [mm] [Graph 6] Allowable load mass by stroke 32 [Graph 5] Allowable load mass by stroke 25 100 100 y, z + A = 0 y, z + A = 0 y, z + A = 50 y, z + A = 50 10 Load mass [kg] Load mass [kg] 10 y, z + A = 100 y, z + A = 100
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
Please contact SMC when the AC welding current exceeds 16000 A.
0 @3 @2 y u #5 y $5 CY1F15 Detailed view of driving cylinder CY1F25 Detailed view of driving cylinder @7 Section A-A Component Parts Note Material No. Description Note 25 26 27 28 Material No.