SMC Corporation of America
Elite Part Number Search
Search Results "12-CY3R20TN-250N"

Recommended tightening torque (Nm) Thread size 1/4 Torque 12 to 14 -9- (2) Do not apply torsion or bending moment other than the weight of the product itself.

Recommended tightening torque (Nm) Thread size 1/4 3/8 1/2 Torque 12 to 14 22 to 24 28 to 30 -9- (2) Do not apply torsion or bending moment other than the weight of the product itself.

No.D-S-OMB0023-C PRODUCT NAME Solid State Auto Switch MODEL / Series / Product Number D-S9### D-T99### D-S7### D-T79### Table of Contents Safety Instructions 2 Model Indication and How to Order 8 Summary of Product parts 11 Definition and terminology 11 Mounting and Installation 12 Installation 12 Circuit diagram 14 Troubleshooting 15 Specifications 19 Dimensions 20 -1No.D-S-OMB0023-C Safety

When failure such as "Insufficient sealing" occurs, please replace the whole product. 12 5.

Dimensions 12 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.

Ext Indicates the status of enhanced diagnosis region (bytes 6 to 12) -16No.EX-OME0014-F Byte1: Station Status 2 Bit 7 0 0 X X X 0 1 0 X Diag. Prm_Req 1 when the SI unit setting is rewritten by the master Diag. Deactivated 1 when SI unit is stopped Reserved Diag. Stat_Diag 1 when it has a diagnosis Diag. Sync_Mode 1 when Sync command is received Diag.

No.PS-OMG0004-D PRODUCT NAME Pressure Sensor MODEL / Series / Product Number PSE54# Table of Contents Safety Instructions 2 Model Identification and How to Order 8 Definition and terminology 8 Mounting and Installation 9 Wiring 9 Troubleshooting 11 Specification 12 Specifications 12 Dimensions 14 -1No.PS-OMG0004-D Safety Instructions These safety instructions are intended to prevent hazardous

Table 3 Thread size Appropriate tightening torque 1/8 3 to 5 1/4 8 to 12 3/8 15 to 20 1/2 20 to 25 (2) If the product is mounted with excessive 2) The outside diameter of polyurethane tubing torque, some sealant will seep out. Remove the excess sealant. swells when internal pressure is applied; therefore, it may not be possible to re-insert used tubing into One-touch fittings.

Dimensions 12 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.

(Take care not to scratch the O ring groove. > Step 3 O-ring Installation surface of the O-ring Body Remove the outer seal O-ring from the Body (Take care to prevent the mounting surface of O ring from being damaged ) 12 XL*-OMJ0003-D 6-3. Assembly Procedure Step 1 Step 2 O ring groove Clean cloth Valve Ethanol Assemble parts eliminating any dust or debris.

ZL-OM00801 Contents Safety Instructions 2 Model Indication and How to Order 10 Mounting and Installation 12 Air Supply 12 Supply Pressure 13 Piping 13 Solenoid Valve 15 Construction 15 Maintenance and Inspection 17 Exhaust from Ejector 19 Specifications 19 Circuit Diagram 22 Weight 23 Exhaust Characteristics and Flow Characteristics of Ejector 24 Flow Characteristics Curves 25 Vacuum Pressure

Tightening torque for piping Connection threads Proper tightening torque Nm Lubrication 1/8 7 to 9 1/4 12 to 14 Caution Caution Caution Caution 3/8 22 to 24 Lubrication 1)The valve has been lubricated for life at the factory, and does not require any further lubrication. 2)In the event that it is lubricated, use class 1 turbine oil (without additives), ISO VG32.

For example, install a ventilation opening, etc. in order to prevent pressure from increasing inside of the confined area and to release the heat generated by the valve. 12.Extended periods of continuous energization If a valve will be continuously energized for an extended period of time, the temperature of the valve will increase due to the heat generated by the coil.

Warning Rc1/8 7~9 Rc1/4 12~14 Rc3/8 22~24 6. Piping to products When piping to a product, refer to the instruction manual to avoid mistakes regarding the supply port, etc. 6 No.VQZ100V-OMK0002-B VQZ Series Precautions for 3/5 Port Solenoid Valve Be sure to read before handling. Refer to main text for detailed precautions on every series. 5.

(Refer to the specifications.)Please contact SMC when using a fluid other than compressed air (including vacuum).We do not guarantee against any damage if the product is used outside of the specification range. 12.

Cross pointed driver Torque driver Tightening torque 0.60.05 Nm See Check item for tightening torque of two screws. 12 8.

If the fitting within the applicable range is selected, there will not be any interference. 12 No.VF1000-OMN0002-A TROUBLE SHOOTING Should any trouble be found during operation, trace the source of the trouble in the following order and take corrective action.

When an actuator, such as a cylinder, is to be driven using a valve, take appropriate measures (such as the installation of a cover or the restricting of access to the product) to prevent potential danger caused by actuator operation. 12. Extended periods of continuous energization 3.

(See Table 4 on page 15.) 11 - Table 3 Auto Switch Mounting Bracket / Part No. 12 - 17.5 17.5 17.5 17.5 17.5 17.5 13 - 14 - Table 4 Minimum Stroke for Auto Switch Mounting 15 - Table 5 Operating Range 16 - Auto Switch Connection and Example 17 - 3. Maintenance Caution For the CJ2-*Z series, the cover and cylinder tube are joined by rolling crimping, and cannot be disassembled.

(Refer to Chapter 7, Parts Replacement Procedure (P. 11 to 12) for details.) 5 XL*-OMI0013-B 2. Product Specific Precautions 2 Precautions 2 Be sure to read before handling Maintenance Parts Caution SMC specified parts should be used for maintenance service. Maintenance can be done without removing a pipe. Remove the four hexagon socket head cap screws on the top of the cover.