IZD10_eng Timing chart .12 7. Exterior dimensions.12 1 1. Safety Instruction These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard by labeling "Caution", "Warning", and "Danger". To ensure safety, be sure to observe ISO4414 and other safety precautions.
PAB-OM-E001-F PRODUCT NAME Process Pump MODEL / Series / Product Number PA(P)3310 Series Contents Safety Instructions -P.2 to 3 Names and functions of parts P.4 Precautions P.5 to 9 Applicable Fluids P.10 Specifications P.11 Performance Curve P.12 to 13 Working Principle P.14 Maintenance Parts P.14 Piping and Operation P.15 Dimensions P.16 1 Safety Instructions These safety instructions are
Connection thread Proper tightening torque (Nm) Rc, NPT, G, PNTF 1/4 12 to 14 Rc, NPT, G, PNTF 3/8 22 to 24 4. Air Supply Warning 1. Use clean air. Do not use compressed air that includes chemicals, synthetic oils containing organic solvents, salinities or corrosive gases, etc., as it can cause damage or malfunction. 2.
Also, it should be noted that the discharge rate will be less than the normal condition. 2) Air consumption Air consumption Air consumption (L/min [ANR]) Caution 16 -If the compressor output is selected SUP=0.5MPa L/min[ANR] 14 SUP=0.35MPa based on air consumption, 0.75kW 12 10 per 100L/min(ANR) is the guide.
Construction and operating principle P.12 10. Operating principle -P.12 11. Sensor mounting (leakage sensor) -P.13 1 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Designated nozzle: IBG1-12-10: Nozzle length (50, 100, 150, 300) Silencing nozzle: IBG1-12S Set including the designated nozzle and silencing nozzle: IBG1-12-10-S : Nozzle length (50, 100, 150, 300) 4. Impact resistance of the product is 150[m/s2]. Vibration resistance is 30[m/s2]. Avoid applying vibration exceeding the allowable value to the product. Mounting Warning 1.
(Take care not to scratch the O ring groove. > Step 3 O-ring Installation surface of the O-ring Body Remove the outer seal O-ring from the Body (Take care to prevent the mounting surface of O ring from being damaged ) 12 XL*-OML0013-B 6-3. Assembly Procedure Step 1 Step 2 O ring groove Valve Clean cloth Ethanol Assemble parts eliminating any dust or debris.
Place the O-ring on the O-ring mounting surface. 12 XL-OMO0001-A Step 5 O-ring Bellows holder Wipe off any dust from the valve seal O-ring and the Bellows holder surface.
Period and scope of warranty The warrantyd period covers the period which finishes the earliest among 0.1 million operating cycles [with our durability test conditions], 18 months after shipping from us, and 12 months after starting the use of the product at your place or your customers place.
. <> 1 Ass 'y () ( ) < SUS304> 7 (SUS304) () () 3 < SUS316L> 6 (SUS316L) < SUS304> 5 (SUS304) () 2 4 (A6063) < A6063> C D E E F C H B G A A mm A B C D E F G H XLH-16 40 100.5 38 1 30 17 35 XLH-25 50 114 48 1 12 40 26 41 XLH-40 65 162.5 66 2 11 55 41 57 XLH-50 70 179.5 79 2 11 75 52 70 8 XL-OMY0003 5 10 []18 12 O 1) FKM M 10 FKM : 110 Pa <> 9 XL-OMY0003 6 6-1. 1 1P4P5
Period and scope of warranty The guaranteed period covers the period which finishes the earliest among 0.5 million operating cycles [with our durability test conditions], 18 months after shipping from us, and 12 months after starting the use of the product at your place or your customers place.
(Refer to Section 7 Parts Replacement Procedure (pages 10 to 12) for details.) 2. Product Specific Precautions 2 Common Specific Precautions 2 Be sure to read before handling Maintenance Parts Caution Only SMC specified parts should be used. Please refer to operation manual. The handle assembly should also be replaced when changing the seal material.
FGDT,F(L250) (7)(9)(11)(12)(13) (14)(15)(16)(17) FGD-CA003 FGDT,F(L500) L500 (18) FGD-CA004 FGDC,E(L250) FGD-CA005 FGDC,E(L500) 7/11 FGX-OM-L007-C 2. 2.
When embedded O-ring Air Machining dimensions for mounting Sealed with O-ring Air Bore size (mm) Stroke A B C D E F G 5 12 8.5 6 4 3.5 M8X1.0 6.5 3 10 20 16.5 14 15 28 24.5 22 5 16 12.5 10 6 3.5 M10X1.0 8.5 3 10 23 19.5 17 15 30 26.5 24 5 17 13.5 10.5 10 3.5 M15X1.5 12 4 10 23.5 20 17 15 30.5 27 24 5 19 14.5 11.5 16 4.5 M22X1.5 19 5 10 25 20.5 17.5 15 31.5 27 24 Note) E and F should be machined
OUT() DC(-) DC(+) PSE57--28 420 mA N.C. 500 (24 V ) 100 (12 V ) OUT() DC(-) -13No.PS-OMS0004CN-D (A/D ) () 20 2030 -14No.PS-OMS0004CN-D PSE570 PSE573 PSE574 01MPa -100100 kPa 0500 kPa 3.0MPa 600 kPa 1.5MPa oC) oC) (25 ) 2F.S.(050 3F.S.(050 oC) oC) 3F.S.(-1060 4F.S.(-1060 PSE57PSE57--28 DC1224 V1010% 10 mA 420 mA 15 V 1 k 500 (24 V ) 100 (12 V ) (25 oC) 1.0F.S. 0.5F.S. oC)
Auto switches When an auto switch is mounted or its set position is changed, refer to pages 12 to 17. C a u t i o n Use a specific mounting bracket (Table 2) and mount the product so that the band of the bracket will be perpendicular to the stroke of the product. Tighten mounting screws to the appropriate torque.
PTFE X446 GR-F-005(5g) 1) 25 2) () 5. 11. 26 6. 12. 27 Revision history 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 URL http://www.smcworld.com Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. 2012 SMC Corporation All Rights Reserved
AF AR 1) 2 3 1) () 2) 5 3) 4) 5 5) 6) 7 2-2. 1) 2) 3) 4) 5) 6) 7) 8) , 9) 10) 3 11) 12) () 13)/ 14) 8 1 P142. 2 3 4 5 6 7 2-3. 1 2) 3 4 5 9 1 P14[2. ] fR[N] [mm] 1. 2 3 10 4 51 1.
Note 5) D-P3DWA cannot be mounted on bore size 32. 24 - < Applicable Auto switches > Solid state switch D-P4DWL How to mount and move the auto switch Fig. 12 Put M4x0.7x8L (2pcs.) into the tapped part for M4 on the auto switch mounting bracket and turn them lightly into the tapped holes.
Before restarting the equipment, confirm that measures are taken to prevent sudden action. -12- 2-4.