HEC-OM-S019 In the case the alarm cant be reset by above manner, repair is required. Others Remove a possible cause and restart. In the case the alarm cant be reset by above manner, repair is required. If the temperature cannot be stable at default value, perform auto tuning.
Hold/Release success: default output DO[101] Hold/Release failure: default output DO[102] * Digital output port can be selected within DO[101] to DO[112] * you select the same digital output port for different status signals, a warning message will be displayed. 2. Test run The manual operation of the magnet gripper unit can be checked.
The stop and skip valves must be normally closed.
N373 Check Valve with One-touch Fitting AKH/AKB Series Bushing Type Can be used in applications with splashing coolant and spatter, etc.
T unit Can be connected with PLC I/O card for serial transmission.
Note 1) Pressure set adjustments must be made in accordance with the operating conditions. Note 2) Set pressure adjustment must be made during the initial operation after the pressure in the cylinder has been released. Note 3) If the set pressure is adjusted too low, it will not be possible to prevent sudden extension during the initial operation.
They cannot be integrated into a unit. Conditions: Operating pressure 0.5MPa, Operating oil Turbine oil Class 1 (ISO VG32), Piping length 1m AS420-02, 03, 04 AS500-06 AS2000-01, 02 AS600-10 AS3000-02, 03 AS4000-02, 03, 04 Circuit 4.12-12
Tube coupler IN-442-5 Pressure probe Pressure can be supplied or stopped by inserting or removing the tube. Finger valve Pressure can be easily applied or released by switching the control. Used in combination with the pressure probe (IN442-5), total pressure can be easily measured. For specifications, refer to page 14-12-4. 14-12-2 3 Precautions Be sure to read before handling.
Tube coupler IN-442-5 Pressure probe Pressure can be supplied or stopped by inserting or removing the tube. Finger valve Pressure can be easily applied or released by switching the control. Used in combination with the pressure probe (IN442-5), total pressure can be easily measured. For specifications, refer to page 14-12-4. 14-12-2 3 Precautions Be sure to read before handling.
If the temperature in the piping becomes lower than the dew point of the compressed air, vapor will be generated. The vapor cannot be exhausted (cannot be pushed out) as the volume of the actuator is small. 1 Exhaust Solenoid valve Piping (Tube) Cylinder 2 3 Vapor is generated.
Since the products specified here are used in various operating conditions, their compatibility for the specific system must be based on specifications or after analysis and/or tests to meet your specific requirements. Be particularly careful in determining the compatibility of the fluid to be used. 2. Only trained personnel should operate machinery and equipment.
on the connections will be Nickel (no plated).
There may be the case it will vary substantially depending on an ambient environment.
Open/ Close success: default output DO[101] Open / Close failure: default output DO[102] workpiece drop detection: default output DO[103] * Digital output port can be selected within DO[101] to DO[112] * you select the same digital output port for different status signals, a warning message will be displayed. 2. Test run The manual operation of the air gripper unit can be checked.
When the number of tubes to be used is less than 6 (DM6) or 12 (DM12), the positioning of the tube should be symmetrical to the center.
Note 1) No freezing Note 2) This product cannot be used in water.
Assembly 1) Terminal box e connected with housing r should be reinstated.
At that time, insulate the lead wires that will not be used. 6. Because this is an open style, it cannot be used where water or oil splashes. 7. It cannot be used if a water hammer or pulsation pressure is applied to the fluid. 8.
(Example) For 6 stations 06 -7- 2-2 Specifications Specifications Remarks Fluid Air, Nitrogen This product cannot be used in an environment exposed to chemicals. Note) It may cause damage to the body. Operating pressure -1000kPa Vacuum release pressure MAX.0.5MPa Pressurised condition cannot be kept.