SI unit for Ethernet POWERLINK Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
C a u t i o n ~ Do not touch the cylinder during high speed and high frequency operation of the cylinder. When the cylinder is operating at a high speed and high frequency, the cylinder tube surface temperature increases, and may cause a burn. 5 ~ Do not use the air cylinder as an air-hydro cylinder.
Model MXY6 MXY8 MXY12 Allowable kinetic energy for intermediate stop (J) 0.007 0.014 0.047 8-9-14 14 Series MXY Specific Product Precautions 2 Be sure to read before handing. Operating Environment Caution Mounting Caution 8. Do not attach magnets to the table section.
The graphs do not show the loadable mass. Refer to the Model Selection for the loadable mass.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not move the cover upward inadvertently during end plate installation.
Do not move the cover upward inadvertently during end plate installation.
Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these . 2. Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction. 3. Do not use in a place subject to heavy vibration and/or shock. 4.
Do not use valves in atmospheres of corrosive gases, chemicals, salt water, water or steam, or where there is direct contact with same. 2. Do not use in explosive atmospheres. 3. Do not use in locations subject to vibration or impact. 4. Do not use in locations where radiated heat will be received from nearby heat sources. 5.
(Fig. 13, 14) Body ported type Box type Fig.13 Fig.14 12 - Doc. no. ZH-OM00401 Construction Specifications 13 - Doc. no. ZH-OM00401 14 - Doc. no. ZH-OM00401 15 - Doc. no. ZH-OM00401 Circuit Examples Caution Select the related air preparation equipment with appropriate size in reference to the circuit example below.
-20-9 Mist Separator 14-20-16 Micro Mist Separator 14-20-22 Odor Removal Filter 14-20-42 Note: Some models have different heights depending on the port size.
Do not use in atmospheres contacting corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not use in explosive atmosphere. 3. Do not use in locations subject to vibration or impact. 4. Do not expose to direct sunlight for an extended period of time. Protective cover should be used to shield. 5.
Do not increase the operating speed after setting the operating conditions.
VS7 S kit (Serial transmission) Kit F kit (D-sub connector) T kit (Terminal block) P kit (Flat cable connector) U S F 15 pin U S P 26 pin U S A S U S P 20 pin U S P 16 pin U S P A B C 10 pin F 25 pin T2 T1 Model Max. number 16(1) 14 8 8 16 16 16(1) 14 16(1) Note 1) Due to the limitation of internal wiring.
Refer to pages 14-21-3 to 14-21-4 for Safety Instructions and Common Precautions. AL Selection Procedure for Assembling the Cover Ring Assembly Caution Pressure gauge for general purpose Pressure switch Cover ring 1. Do not apply high load voltage (current) or surge current as this can cause the switch to malfunction. 2.
H D DO 2 01 1 8 1 8 Base mounted 02 1 4 1 4 Caution Refer to front matters 58 and 59 for Safety Instructions and pages 3 to 7 for 3/4/5 Port Solenoid Valve Precautions.
20 11 22 14 60 60 129 MB-SIO . 100 11 4 \20 90 15 158 132 \84 26 13.5 24 17 75 100 '29 25 +008001 (mm) [~ "r.
Do not disassemble the product or make any modifications, including additional machining. Doing so may cause human injury and/or an accident. 14.
Do not use the drain tube in an upward direction. Do not bend or crush the drain tube. (Operation of auto drain will stop and water will flow out through the air outlet.) When tightening piping at the air inlet/outlet tube, the nozzle should be held firmly with a pipe wrench.
Do not apply excessive force or shock to the body or fittings with an impact tool. It can cause damage or air leakage. 100 8 7 to 9 150 1/8 14 12 to 14 200 1/4 17 22 to 24 200 3/8 21 28 to 30 200 1/2 24 Lock Nut Tightening Torque Caution 1. Suitable screw torque for a hexagon lock nut is shown in the table below.