1 High Purity Chemical Valve Compact Type Series LVD VC Space saving, compact type is available. Space saving, compact type is available. VDW Compact type is introduced as a new series to complement VQ Body: New PFA Body: New PFA Body: New PFA conventio Using the chewed portion of the tube as it is can cause problems such as leakage or difficulty in removing the tubing. 1. Do not use in a location having an explosive atmosphere. 2. Do not operate in locations where vibration or impact occurs. 3. Do not use in locations where radiated heat will be received from nearby heat sources.
When the SET button is pressed continuously for 4 seconds or more, the display changes as shown in .
If the guide rod has twisted, operation resistance will become abnormally higher and the bearing will wear at an early stage, thereby resulting in poor performance. e Allow an ample space around the cylinder so that no obstruction will occur for checking and maintenance. r Do not adjust the rod stroke by moving the rear plates, as doing so will cause the rear plates to come into direct contact
30 40 With back flow mechanism Note) AW10 comes with a back flow mechanism as a standard feature.
19 1 Communication connector 2 c Cable length: 0.2m 20 View c 315
It turns OFF when an alarm occurs or when JOG movement takes place.
The response time becomes quicker as the set value becomes larger. Additionally, the response time becomes quicker as the piping length becomes shorter.
Also, keep the manual where it can be referred to as necessary. 6. Tighten the nut to the end surface of the body. As a guide, refer to the proper tightening torques shown below.
AXT100-20-2-05 AXT100-20-2-06 AXT100-20-2-01 AXT100-20-2-02 AXT100-20-2-03 AXT100-20-2-04 Clip Circuit with light PR plate qChanging the piping direction from in-line to perpendicular (port on the valve) is possible on the VQZ100 series. Follow the steps below to change piping direction: Remove the fitting clips that hold the fitting and port plug in place.
Caution Mounting 1) Do not subject the gauge to shocks, such as dropping during transportation and mounting, as this can cause loss of indication accuracy. 2) Do not use this gauge in a location with high temperature and humidity, as this may cause faulty operation. 3) When mounting the pressure gauge, be certain to use a wrench on the square wrench flats to screw it into place.
License Agreement SMC Corporation (hereinafter referred to as "SMC") hereby grants the user (regardless of whether the user is a corporation or an individual) a license to use this software "IP Address Setting Tool" (hereinafter referred to as "Software") according to this License agreement (hereinafter referred to as "Agreement") under the articles listed below.
(reference value) 11-LEJS40* Speed 600mm/sec Speed 1200mm/sec 100,000,000 100,000,000 10,000,000 10,000,000 ISOclass8 ISOclass8 0/mi n( AN R ) ISOclass6 1,000,000 1,000,000 ISOclass7 ISOclass7 Particl concentration[Particls/m 3] Particl concentration[Particls/m 3] 100,000 100,000 0/mi n( AN R ) ISOclass6 10,000 10,000 ISOclass5 ISOclass5 50/mi n( AN R ) 20/mi n( AN R ) 1,000 1,000 ISOclass4
T h e V YH y R e g R a n g e i s c o n s t r u c t e d b y u t i l i z i n g a standard control unit either alone (VY1D00-M5) or as a Pilot Valve controlling one of the Range of VEX1 Power Valves.
Two Hand Control Valve VR51 Series RoHS An output is available through synchronized, twohanded operation (within 0.5 s)!
Corxtruction./ Parts List 27A' PartsList Note: The rotation specilication of270', the point of minimum rotation 20' is a limit shifring point even il the switch is shifted to make rotation of switch as shown in the left diagram. (E\ren if switch is shitted tothe maximum, switchon will be made at the point prior to the stopping ooint at 20'.)
Corxtruction./ Parts List 27A' PartsList Note: The rotation specilication of270', the point of minimum rotation 20' is a limit shifring point even il the switch is shifted to make rotation of switch as shown in the left diagram. (E\ren if switch is shitted tothe maximum, switchon will be made at the point prior to the stopping ooint at 20'.)
ANA1-01 to 06 ANA1-06: PP How to Order ANA1-01 to 20 A1 03 AN Port size Symbol Port size Connection 01 1 8 02 1 4 03 3 8 04 1 2 Screw-in 06 3 4 1 4 10 1 12 1 1 2 1 14 20 2 Model (One-touch fitting connection) C08 (8 One-touch fittings size) Effective area (mm2) Weight (g) ANA1-C08 11 5 58 16 A B Dimensions (mm) Model One -touch fitting size 8 10 12 C10 (10 One-touch fittings size) One-touch
As a rule, it should be tightened an additional 15 to 30 apply pressure evenly around Ihe collar so that il goes slraighl down. 2. Pull out the tube while holding down the release bushing so Ihat il does not come out.
The purpose of an air cushion is not to reduce the speed of a piston as it nears the stroke end.