180 A part B part Procedure Calculation Calculation example 1. Check the operating conditions, dimensions of attachment, etc. Operating model: MHY2-16D Opening time: 0.15 s a = 40 (mm) b = 7 (mm) c = 8 (mm) d = 5 (mm) e = 10 (mm) f = 12 (mm) A part a b c B part e f d 2.
B 1.8 1.6 Groove position of auto switch A 10.4 12.8 Model MHK2-12 MHK2-16 A B Dimensions A and B of other models are same as standard switch grooves. Standard switch grooves 12-6-17
Use this as a standard when mounting, etc. Auto switches have hysteresis similar to micro switches. Use the table below as a guide when adjusting auto switch positions, etc.
Use the table as a guideline for mounting. Auto switch mounting bracket part no. BMG2-012 Auto switch part no. D-M9(V)/M9W(V)/M9A(V) Note) Use a screwdriver with a grip diameter of 5 to 6 mm to tighten the set screws (M2.5). The tightening torque should be 0.5 to 1 Nm. As a rule, it should be turned about 90 beyond the point at which tightening can be felt.
Use this as a standard when mounting, etc. Auto switches have hysteresis similar to micro switches. Use the table below as a guide when adjusting auto switch positions, etc.
Make sure to connect a speed controller and adjust it to a speed of 500 mm/s or less to operate the cylinder.
Make sure to connect a speed controller and adjust it to a speed of 500 mm/s or less to operate the cylinder.
INFORMATION 50 mm 50 mm Magnet Gripper Adsorbs and Holds with a Magnet Steel plates can be transferred without a vacuum. Supports workpieces with holes and uneven surfaces where a vacuum pad cannot be used.
Fittings & Tubing Air Cylinders Rotary Actuators Side tapped mounting [1/N1] Through-holes in open/close direction [2/N2] 4 x MM through Thread for mounting attachment C C B A 4 x H through Hole for mounting attachment S S O O B A (mm) (mm) MM M2.5 x 0.45 M3 x 0.5 M4 x 0.7 M5 x 0.8 C 2 2.5 4 5 H 2.9 3.4 4.5 5.5 B 5.7 7 9 12 B 5.7 7 9 12 Model A 3 4 5 6 Model A 3 4 5 6 11221122112211221 N1
MHT2-63D L = 180 mm Warning Maintenance If a workpiece is to be gripped by using the toggle, make sure to periodically check that the workpiece has not shifted during the acceleration of the movement. If the workpiece is not gripped in a stable manner, it could shift or drop and create a dangerous situation.
MHT2-63D L = 180 mm Warning Maintenance If a workpiece is to be gripped by using the toggle, make sure to periodically check that the workpiece has not shifted during the acceleration of the movement. If the workpiece is not gripped in a stable manner, it could shift or drop and create a dangerous situation.
, Cylinder Type: Rectangular, Cylinder Nominal Designation Size(φ): 25, Port thread type: Rc, Port position: N/A, Switch: M9NV, Lead wire(m): 3, Number Of Switches: 2 pcs., Custom-made specifications: N/A, Connector Type: N/A, Type of Rod end thread: Male thread, Cylinder with improved water resistance: N/A
Order a stainless steel screw kit (BBA1) separately, and use the M4 x 6 L stainless steel set screws included in the BBA1. Note 5) There is a difference in the cylinder tube thickness depending on the cylinder model. Use caution when a band mounting type is used as an applicable auto switch and a cylinder model is changed.
, Cylinder Type: Rectangular, Cylinder Nominal Designation Size(φ): 25, Port thread type: Rc, Port position: N/A, Switch: M9NV, Lead wire(m): 3, Number Of Switches: 2 pcs., Custom-made specifications: CH□QHB compatible product (through bolt), Connector Type: N/A, Type of Rod end thread: Male thread, Cylinder with improved water resistance: N/A
Series CJ2 is auto switch capable Standard double acting single rod, Bore sizes: 6, 10, 16 *, Strokes from 15mm through 200mm depending upon bore size, Mounts: basic, foot, front flange, double clevis, Variety of switches and a variety of lead wire lengths CJ2 ROUND BODY CYLINDER. CYL, RND BODY, D/CLVS. ACTUATOR. 10MM CJ2 DBL-ACT AUTO-SW. 0.44092 lb. EE.
, Cylinder Type: Rectangular, Cylinder Nominal Designation Size(φ): 25, Port thread type: Rc, Port position: N/A, Switch: M9NV, Lead wire(m): 3, Number Of Switches: 2 pcs., Custom-made specifications: CH□QHB compatible product (through bolt), Connector Type: N/A, Type of Rod end thread: Male thread
Magnet: D (Built-in Magnet), Series: A2 (Standard), Mounting: T (Center Trunnion), Tube Material: Aluminum Tube, Bore Size: 40mm, Port Thread: Rc, Stroke A: 75mm, Rod Boot A: None, Cushion A: Air Cushion, Stroke Adjustment: A (0 to 25mm), +: None, Stroke B: None, Rod Boot B: None, Cushion B: Air Cushion, Pivot Bracket: w/o Bracket, Rod End Bracket: w/o Bracket, Auto Switch: M9NV--Solid State
Magnet: Built-in Magnet, Series: Standard, Mounting: Center Trunnion, Tube Material: Aluminum Tube, Bore Size: 40mm, Port Thread: Rc, Stroke A: 75mm, Rod Boot A: None, Cushion A: Air Cushion, Stroke Adjustment: 0 to 25mm, +: None, Stroke B: None, Rod Boot B: None, Cushion B: Air Cushion, Pivot Bracket: w/o Bracket, Rod End Bracket: w/o Bracket, Auto Switch: M9NV--Solid State, Gen.
This is a legacy product. Please contact us for the latest version.sales@ocaire.com, CYL, RND BODY, D/CLVS, D/ACT, ACTUATOR, CJ2 ROUND BODY CYLINDER, EE, 10MM CJ2 DBL-ACT AUTO-SW
3-wire (NPN), Number Of Switches: 2 pcs., Lead wire length: 3 m, Gripper internal diameter(φ): 10, Angle of rotation(°): 90, Auto switch for rotation detector: M9NV, Number of switches for rotation detector: 2 pcs., Lead wire length for rotation detector: 3 m, Connector type for gripper opening/closing: None, Connector type for rotation detector: None