IDUS/IDFS Install a suitable circuit breaker applicable to each model. Use a circuit breaker having a sensitivity current of 30mA or less and a rated current of 5A.
Water Hammer Characteristics VNC1 (N.C. 0.49 MPa) Conditions: Piping 30 m Steel tube, total pressure 0.49 MPa VNC4 (N.C. 0.97 MPa) Conditions: Piping 30 m Steel tube, total pressure 0.97 MPa 2.5 15A Peak pressure at valve closed (MPa) Peak pressure at valve closed (MPa) 8A 25A 2 1 20A 32 A F 15A 20A 40 A F 32 A F 1.6 0.8 25A 40 A F 50 A F 65F 50 A F 1.2 0.6 80F 65F 80F 0.8 0.4 0.4 0.2 0 1
When a switch-mode power supply is connected to the product, switching noise will be superimposed and the product specification can no longer be met. This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switch-mode power supply and the product or by using a series power supply instead of a switch-mode power supply.
Fieldbus system Instruction Manual Wiring A two bit DIP-switch and a six bit DIP-Switch Two DIP-switches SW2 and SW3 are under the M12 safe input connector box. To access the switches remove the retaining screws as shown below.
It is important to understand that one may follow this guides recommendation, yet have a failure due to a parameter specific to the given application, as noted.
This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switch-mode power supply and the product, or by using a series power supply instead of a switch-mode power supply.
Proper selection with body and sealing materials permits application with a wide variety of fluids such as air, water, oil, gas and vacuum.
(Not a\ailabl on NCRBI BWl0) x ( ) : When porl A is pressunzed. x x Optional M3 fiiing available S ho/r lo ofder page NCDRBIOWIQoI$ol[r$Q Rotation Time Setting Bodg To k Used As A Flange ltcRElB\ltfto Actual Torque Even a small torque generated by the rotary actuator, due to inertia, can cause damage. Therefore.
Air tank 41l PA=0.7 MPa A=0.7 MPa Air tank 20l PA=0.7 MPa Air tank 20l PA=0.7 MPa A=0.7 MPa Air tank 41l PA=0.7 MPa Air tank 20l PA=0.7 MPa A=0.7 MPa Air tank 20l PA=0.7 MPa 6 x 6 pcs.
This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switch-mode power supply and the product, or by using a series power supply instead of the switch-mode power supply. Operator 3. Press the button to complete the setting. The Pressure switch operates within a set pressure range during window comparator mode.
VR VH VHS Pilot port (A side) 2-M5 x 0.8 sub-plate side (P , A, B port) (R1, R2 port) 2 position double: VZA4241--01 02 Pilot port (B side) Body side Pilot port (A side) 2-M5 x 0.8 body side 2-4.5 Mounting hole Pilot port (A side) 2-M5 x 0.8 sub-plate side (R1, R2 port) (P , A, B port) Pilot port (B side) Sub-plate side 5-3-7 8 Series VZA4000 Dimensions: Base Mounted 3 position closed center
When a switch-mode power supply is connected to the product, switching noise will be superimposed and the product specification can no longer be met. This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switch-mode power supply and the product or by using a series power supply instead of a switch-mode power supply.
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
(Not a\ailabl on NCRBI BWl0) x ( ) : When porl A is pressunzed. x x Optional M3 fiiing available S ho/r lo ofder page NCDRBIOWIQoI$ol[r$Q Rotation Time Setting Bodg To k Used As A Flange ltcRElB\ltfto Actual Torque Even a small torque generated by the rotary actuator, due to inertia, can cause damage. Therefore.
A A A B A B P1 B B Section A-A (ejector) Section B-B (solenoid valve) Replacement parts list Parts list No. 1 2 3 4 5 6 7 8 Description Material No. Description Part No.
Also, keep the manual where it can be referred to as necessary. Piping Warning 1. To screw a piping material into a component, tighten with the recommended tightening torque while holding the female thread side. Operating Environment If the tightening torque is not enough, looseness and seal failure can occur.
Enlarged view of part A A 0 3 Do not use the product in a place where static electricity is a problem. Otherwise it can cause failure or malfunction of the system.
Replace the product with a new one right away when it reaches its life. Make sure to verify the operating conditions of the actuator at least once a day.
There is a risk of unexpected malfunction. Do not use solvents such as benzene, thinner etc. to clean each unit. They could damage the surface of the body and erase the markings on the body. Use a soft cloth to remove stains. For heavy stains, use a cloth soaked with diluted neutral detergent and fully squeezed, then wipe up the stains again with a dry cloth.
a place that will be used as a scaffold during piping.