If both plug and socket sides have connectors for SPEEDCON, the cable can be inserted and connected by turning it a 1/2 of a rotation, leading to reduction in work hour. A non-compatible connector can be connected to a compatible connector as well as an M12.
Caution Proceed carefully, as incorrect wiring can cause damage. Use DC power supply with sufficient capacity and a low ripple. Turn off the power supply to remove and insert the connector. Never turn the right angled type connector as it is not designed to turn.
This product operates as a slave. It does not send any requests.
Lower or raise supply pressure a little at a time, and use in a supply pressure range where the intermittent noise does not occur. Clogging of the silencer Replace the silencer. Add a filter to supply (compressed) air circuit. Clean the mesh periodically as necessary by washing, air blow and so on or replacing plate B. Refer to 7.2 Maintenance for suction cup.
As some parts of the air dryer will remain hot, there is a risk of burns due to residual heat after the power is switched off. So do not carry out replacement work until the temperature of these parts has fallen to 50 or less. Wait for about 10 to 15 minutes as a guide.
As a result, it could pose a hazard to humans and damage the machinery and equipment. 11) Do not use until you can verify that equipment can operate properly.
Release of residual pressure For maintenance purposes install a system for releasing residual pressure. 1. Operation in a low temperature condition It is possible to operate a valve in extreme temperature, as low as -10 . Take appropriate measures to avoid freezing of drainage, moisture etc. in low temperature. 2.
Applicable model A B C D E F G H J K L t AS-10L ZH05/07/10DA 11 14.8 18.3 3.4 27.5 19.5 3.4 4.9 7.3 12 14 1 AS-25L ZH13/15DA 17 19.6 24.6 4.5 38 28 4.5 6.5 9.5 15.5 20 1.2 AS-30L ZH18/20DA 22 24.8 29.8 43 33 22 1.4 230 Body Ported Type Vacuum Ejector ZH Series Body Ported: ZH05D A--to ZH20D A--S L S L DIN rail mounting bracket (Bracket on a single side) ZH05 to 10DA ZK2 H J E F ZQ ZR G ZB
Error Gr.1 A.320 Regenerative Overload Gr.2 A.330 Main Circuit Power Supply Wiring Error Gr.1 A.400 Overvoltage Gr.1 Alarm A.410 Undervoltage Gr.2 A.450 Main-Circuit Capacitor Overvoltage Gr.1 A.510 Overspeed Gr.1 A.511 Overspeed of Encoder Output Pulse Rate Gr.1 A.520 Vibration Alarm Gr.1 A.521 Autotuning Alarm Gr.1 A.710 Overload: High Load Gr.2 A.720 Overload: Low Load Gr.1 A.730 Dynamic
AS-T (Hexagon width across flats) ASP ASN AQ ASV AK VCHC ASS Metric Size Inch Size ASR ASQ Model d T Weight (g) H D1 D2 L1 L2 L3 L5 (1) A (2) Model d T Weight (g) H D1 D2 L1 L2 L3 L5 (1) A (2) D3 L4 Max.
Error Gr.1 A.320 Regenerative Overload Gr.2 Alarm A.330 Main Circuit Power Supply Wiring Error Gr.1 A.400 Overvoltage Gr.1 A.410 Undervoltage Gr.2 A.450 Main-Circuit Capacitor Overvoltage Gr.1 A.510 Overspeed Gr.1 A.511 Overspeed of Encoder Output Pulse Rate Gr.1 A.520 Vibration Alarm Gr.1 A.521 Autotuning Alarm Gr.1 A.710 Overload: High Load Gr.2 A.720 Overload: Low Load Gr.1 A.730 Dynamic
The 3-port valves on the A and B sides can operate independently. When used as 3-port valves, only half the number of stations is required. Can also be used as a 4-position, 5-port type valve.
Do not use the lock as a safety lock or a control that requires a locking force. The lock used for the product with a lock is designed to prevent dropping of work piece. 2. For vertical mounting, use the product with a lock. If the product is not equipped with a lock, the product will move and drop the work piece when the power is removed. 3.
5 Meter-in type Meter-in type M3 port M5 port U10/32 port 2 tubing type M3 port M5 port U10/32 port 486 Series AS Speed Controller with One-touch Fitting Elbow Type/Universal Type Construction Elbow type Meter-out type AS3201F-02 Universal type Meter-out type AS3301F-02 AS AS TMH ASD AS AS-FE KE AS-FG AS-FP AS-FM Meter-in type AS3211F-02 Meter-in type AS3311F-02 AS-D AS-T ASP ASN AQ ASV AK
Actuator drive When an actuator, such as a cylinder, is to be driven using a valve, take appropriate measures to prevent potential danger caused by actuator operation. 5. Pressure (including vacuum) holding It is not usable for an application such as holding the pressure (including vacuum) inside of a pressure vessel because air leakage is entailed in a valve. 6.
INLET (Upstream) is defined as a port connected to the region below the valve seat. It is illustrated with an arrow pointing towards the valve body or an "empty" triangle on the schematic. OUTLET (Downstream) is defined as a port connected to the region above the seat and below the diaphragm.
Seal storage Caution Pack seals in a sealed package such as a polyethylene bag and store in a box. Avoid direct sunlight and store seals at a low temperature and humidity. Take special care to isolate and shield them from equipment which generates heat, radiation and ozone. Do not pile up a large amount of seals or apply a heavy load, which may result in deformation or damage.
It is the set of files of the main IODD file and image files such as a vendor logo, device picture and device icon. The corresponding IODD files of each product are as follows.
Do not keep the coil assembly warm using a heat insulating material. A tape heater to prevent freezing should be limited only to the piping and body. This can cause the coil to burn out. 5. If the product is installed close to a vibration source, the distance from the body should be as short as possible to prevent resonance. 6.
Note 4) Minimum bending radius is measured as shown left as representative values. Use a tube above the recommended minimum bending radius. The tube may be bent if used under the recommended minimum bending radius. Therefore, refer to the tube close bend radius and make sure that the tube is not bent or flattened.