Information 2 !2 !3 !3 !4 !4 !5 !5 M5 port M5 port y y u u !7 !7 q w e r t q w e r t o o !0 !0 !1 !1 i i !4 !4 !2 !2 !3 !3 !6 !6 Component Parts Description Material Description Material No.
-10AS G46-2-02 G36-2-01 G46-2-02 G46-2-02 G46-2-02 0.2MPa Note 3) GC3-2AS GC3-2AS GC3-2AS GC3-2AS GC3-2AS Note 1) Assembly includes a bracket and set nuts.
M3 ,M5 ,U10/32 R NPT Nil ASN N AQ Model 4 6 8 10 12 5/32"1/4" 5/16"3/8" 1/2" Applicable tubing O.D. (mm) Effective area (mm 2) IN OUT OUT EXH.
AC
Plug conneclor (l Loosen the Phillips head machine screw using a Phillips type scfewdriver 10 remove lhe plate 6 ; ' 6 9 ] 0 : O After exchanging connectors in desired posilions. re affix the plate with a Phillips type screwdriver to the case. (* i l r (Flf -.-.r--r ll U,F* [ tL_ -T Plate r connector Rectanoular lilulti-Connector Series KDM Separation Loosen the clamp bolt to separate the
For a facility having a large installation area (that can vent the air naturally): Make an air outlet on a wall at a high level and air inlet on a wall at a low level, to allow for adequate airflow. 2.
t y e i w Note Manganese phosphate Chromated Description Material Steel Aluminum Steel Steel Synthetic rubber Steel Steel Steel No. 1 2 3 4 5 6 7 8 Stud Case Ring Cap Dust cover Set screw Rod end nut Washer Black zinc chromated Zinc chromated Zinc chromated J J Dimensions JC20 to 63 M Center of sphere M U U D F G P H A R E B Standard type Pneumatic: to 1 MPa (mm) Applicable cylinder bore
model number HRL Series 2.1 Model Number of Product 2-1 HRX-OM-Y098 Chapter 2 Name and Function of Parts 2.2 Name and Function of Parts 2.2.1 HRL-A-20 (Air cooled type) Fig. 2-2 Names of the parts (This drawing shows HRL200-A-20.) 2.2 Name and Function of Parts HRL Series 2-2 HRX-OM-Y098 Chapter 2 Name and Function of Parts Table 2.2-1 Accessory list (1) Operation Manual 2 pcs.
of Parts 2.2 Name and Function of Parts 2.2.1 HRL-A-20 (Air cooled type) Fig. 2-2 Names of the parts (This drawing shows HRL200-A-20.) 2.2 Name and Function of Parts HRL Series 2-2 HRX-OM-W060 Chapter 2 Name and Function of Parts Table 2.2-1 Accessory list (1) Operation Manual 2 pcs.
A Contact output 1 selected alarm Sets alarm which is selected for contact output 1. AL.01 Contact output 2 function Sets output signal function of contact output 2. RMT Contact output 2 operation Sets output signal operation of contact output 2. A Contact output 2 selected alarm Sets alarm which is selected for contact output 2.
A Contact output 1 selected alarm Sets alarm which is selected for contact output 1. AL.01 Contact output 2 function Sets output signal function of contact output 2. RMT Contact output 2 operation Sets output signal operation of contact output 2. A Contact output 2 selected alarm Sets alarm which is selected for contact output 2.
0.1] 10 Note 3) 0 , 5 , 10 D0418 2 Load mass [10g] 5 Yes to 100 Movement mode No D0419 2 1 0 , 1 No. 1 (0: ABS, 1: REL) (No. 0) Note 5) D041A 2 Threshold force value [0.1] 1 1 to 50 Yes D041B 2 Positioning width [m] 1 0 to 30 Yes Yes AREA A position 1 [m] More than D041C 4 1 Note1) 0 Note 1) Yes AREA A position 2 [m] More than D041E 4 1 Note1) 0 Note 1) Yes AREA B position 1 [m] More than
LEFS16A-100 NPN (2) Check Parallel I/O configuration matches (NPN or PNP). (2) 17 -
2.4 Construction
8 r u !7 @9 @6 @5 @7 CK CLK #0 CKQ CKP1C (Clevis width 12.5) i !2 !3 !5 #2 !0 !1 Replacement Parts/Seal Kit Note 1) Seal kits are the same as those of the CKG1/CKP1. Note 2) Seal kit does not come with a grease pack, so please order it separately.
Leakage voltage Particularly when using a resistor in parallel with a switching element and using a C-R element (surge voltage suppressor) to protect the switching element, take note that leakage current will flow through the resistor and C-R element, etc., creating a danger that the valve may not shut OFF.
Do not use the lock as a safety lock or a control that requires a locking force. The lock used for the product with a lock is designed to prevent dropping of work piece. 2. For vertical mounting, use the product with a lock. If the product is not equipped with a lock, the product will move and drop the work piece when the power is removed. 3.
solenoid valve (with a PLC) Possible to operate by using the same signals as those for a solenoid valve (with a PLC) Having both the operationability of an air cylinder and the speed controllability of an electric actuator New actuator concept Machine difference 3 3 Both end position accuracy Speed reproducibility 2 2 Operationability similar to an air cylinder Impact free shifting of the
1 y @2 @3 w !9 r e !7 @1 !2 !6 !8 q !1 A B A' B' Without magnet Extension locking u t @5 @0 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com When shipped Section A-A' Retraction locking !0 !5 Section B-B' !3 !
M5 x 0.8 2 x 4-OA effective depth RA 2 x 4-OB Depth of counter bore RB F Q Y I 4-N through M 0.2 D E L B + Stroke K A + Stroke M 0.2 E 25, 28 H effective thread depth C 2-Rc 1/8 F Q Y 2 x 4-OA effective depth RA 2 x 4-OB Depth of counter bore RB J I 4-N through M 0.2 D W E K L B + Stroke M 0.2 A + Stroke E (mm) Bore size (mm) Stroke range (mm) OA A B C D E F H RB I J K L M N OB Q RA W Y M4