EX9-OEx_PE.eng M3 x 18: 2 pcs. (Hexagon socket head cap screw (with SW)) : Please refer to the separate catalog regarding assembly and disassembly with other unit. Warning: WARNING indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Note Hold together so that there is no gap between units and tighten the screws.
Install the product (with bracket) using the M3 screws (4 pcs.). Bracket thickness is approximately 1.2 mm. Turn the power off and turn it on again. System error An internal data error has occurred. Press the UP button continuously to keep increasing the set value.
Install the product (with bracket) using the M3 screws (4 pcs.). Bracket thickness is approximately 1.2 mm. 2. Press the or button to change the set value. The button is to increase and the button is to decrease the set value. : If the error cannot be reset after the above measures are taken, then please contact SMC.
Flow indicator LED Safety Instructions Square groove Install the product (with bracket) using the M3 screws (4 pcs.). Bracket thickness is approximately 1.2 mm. Power indicator LED Indicates the power supply status. LED is ON (Green) when power is ON. LED is ON (Red) when a system error occurred.
They are all important notes for safety and must be followed in addition to International standards (ISO/IEC) and other safety regulations. 04 Equivalent to M3 (L=6) 20 0.04 to 0.05 Nm 40 Equivalent to M4 (L=10) 0.09 to 0.10 Nm Element Description This unit supplies the fluid from the supply side main piping to the application.
. -14No.PF-OMN0012-H Mounting and Installation Installation Mounting with panel mount adapter Fix the panel mount adapter to the flow monitor with the screws supplied M3 x 8 L (2 pcs.).
Dynamic viscosity [m2/s] Viscosity [Pas] Density [kg/m3] Formulas below can be used for common units 1cP = 1mPas = 10-3Pas 1cSt = 1mm2/s = 10-6m2/s 13 Working Principle 1. When air is supplied, it passes through the switching valve and enters drive chamber B. 2.
Dynamic viscosity [m2/s] Viscosity [Pas] Density [kg/m3] Formulas below can be used for common units 1cP = 1mPas = 10-3Pas 1cSt = 1mm2/s = 10-6m2/s 14 Working Principle 1. When air is supplied to P1 port, it enters drive chamber A. 2. Diaphragm A moves to the left, and at the same time diaphragm B also moves to the left. 3.
Dynamic viscosity [m2/s] Viscosity [Pas] Density [kg/m3] Formulas below can be used for common units 1cP = 1mPas = 10-3Pas 1cSt = 1mm2/s = 10-6m2/s Pulsation Attenuating Capacity The process pump generates pulsation because it discharges a liquid using two diaphragms.
Attach the included filter cover and air filter (hook the protruding part of the filter cover on the product) and tighten screws to the required torque (M3: 0.63Nm). [] key (UP key) Increases set data. [MODE] key Used to change screens and modes.
Step 3 Preparation2 Step 4 Body assembly 3 3 Bolt 1 2 Bolt size, Tool, Tightening torque of bolt (Nm) Valve seal 1 2 1 Bolt size valve Hex Tightening torque wrench size 16 M3 3 0.7 4 4 25 M5 4 1.5 40 M6 5 2.5 Bonnet 50 M8 6 6.1 assembly 63 M10 8 15 80 Body [For XLA-] Pilot port 0.4 MPa [For XLC-] Air should not be applied.
80 Actuating type Double acting(Dual operation) , pressurize to open/close Fluid Inactive gas under vacuum Operating temperature oC 5 to 60 (High temperature type:5 to 150) Operating pressure Pa (abs) Atmospheric pressure to 1 x 10-6 Conductance l/s Note 2 5 14 45 80 160 200 Internal 1.3 x 10-10 for the standard material (FKM) at ambient temperatures , excluding gas permeation Leakage Pa m3
XMH-16 XMH-25 XYH-25 XMH-40 XYH-40 XMH-50 XYH-50 Flange (valve) size 16,CF034 25 40,CF070 50 Actuating type Manual Fluid Inactive gas under vacuum Operating temperature oC 5 to 150 Operating pressure Pa (abs) Atmospheric pressure to 1 x 10-6 Conductance l/s Note 2 5 14 45 80 Internal 1.3 x 10-10 for the standard material (FKM) at ambient temperatures , excluding gas permeation Leakage Pa m3
Table 4 Inner cover fixing screw tightening torque[Nm] Model Screw size Tightening torque CYV15 M3 x 0.5 0.3 CYV32 M6 x 1 2.45 Sine suction mechanism is installed as a standard specification. However, cushion effect adjustment is not available. 7. Maintenance (1) Do not disassemble the cylinder tube, linear guide, slide table and other components.
Inner cover fixing screw tightening torque[Nm] Model Screw size Tightening torque CYP15 M3 x 0.5 0.3 CYP32 M6 x 1 2.45 Sine suction mechanism is installed as a standard specification. However, cushion effect adjustment is not available. 9/11 8. Maintenance (1) Do not disassemble the cylinder tube, linear guide, slide table and other components.
INNER VALVE(B) LOCK NUT (261020) INNER VALVE (A) (M3) (26102) 251 INNER VALVE Assy (26100-6) -8- 7.Countermeasures for failure ! Warning Avoid use when failure is not solved. Phenomenon Cause Countermeasures Dust attach supply port or exaust port Disassemble and clean. (If flawed, replace the part.)
Model Thread size Tightening torque SX3000 M2 0.17 Nm SX5000 M3 0.8 Nm SX7000 M4 1.4 Nm 11 SX3000-OMM0002-B -12-SX3000-OMM0002-B -13SX3000-OMM0002-B TROUBLESHOOTING Should any trouble be found during operation, trace the source of the trouble in the following order and take corrective action.
Connection of fittings When screwing fittings into valves, tighten as follows. (1) Follow the procedures below when installing an SMC fitting, etc. 1) M3 After tightening the fitting by hand, use a wrench to tighten the fitting an additional approximately 1/4 turn.
Cross recessed round head screw for mounting the bottom bracket Square nut Bottom bracket Applicable torque IRV10(A):M3 0.320.03Nm IRV20(A):M4 0.760.05Nm 8 - Caution Handling (1) Reduce the set pressure to zero(atmospheric pressure) for removing the plug when additionally mount the pressure gauge and pressure switch. 1.For customers purchasing regulator with a pressure gauge or pressure switch
Tighten the FG terminal (M3 round head combination screw) firmly with a tightening torque of 0.3 Nm. Tighten the connector fixing screws (M2.5 slotted head screws) firmly with a tightening torque of 0.2 to 0.3 Nm. A. Dual power supplies B. Single power supply Figure 3 Figure 4 : Communication connector FG and FG terminal are connected inside the SI unit.