: [Rc (R)] Rc, Control Side Plumbing Thread Nominal: 3/8, Power Supply Voltage: Single-phase: 100 V AC (50 Hz), 100/110 V AC (60 Hz), Accessory: -, Specification: None, Air Compressor Size: 0.75 kW, Auto drain: None, For Compressed Air Cooling: None, Copper Tube Anti-rust Processing: None, Short-circuit Breaker: None, Power Supply Terminal Block: Yes, Operation, Terminal block for abnormal
Transportable Mass (Vertical)(kg): 2.5, Drive Method: [Slide Screws] Slide Screw + Belt, Guide: Included, Lead(mm): 16, Input Power Supply: DC 24V, Position Detection: Incremental, I/O Module: Not Provided, Table Width W1(mm): 60, Brake: Not Provided, Max. Thrust Force Range(N): 0 to 100, Max.
Transportable Mass (Vertical)(kg): 2.5, Drive Method: [Slide Screws] Slide Screw + Belt, Guide: Included, Lead(mm): 16, Input Power Supply: DC 24V, Position Detection: Incremental, I/O Module: Not Provided, Table Width W1(mm): 60, Brake: Not Provided, Max. Thrust Force Range(N): 0 to 100, Max.
Transportable Mass (Vertical)(kg): 2.5, Drive Method: [Slide Screws] Slide Screw + Belt, Guide: Included, Lead(mm): 16, Input Power Supply: DC 24V, Position Detection: Incremental, I/O Module: Not Provided, Table Width W1(mm): 60, Brake: Not Provided, Max. Thrust Force Range(N): 0 to 100, Max.
Transportable Mass (Vertical)(kg): 2.5, Drive Method: [Slide Screws] Slide Screw + Belt, Guide: Included, Lead(mm): 16, Input Power Supply: DC 24V, Position Detection: Incremental, I/O Module: NPN, Table Width W1(mm): 60, Brake: Not Provided, Max. Thrust Force Range(N): 0 to 100, Max.
Transportable Mass (Vertical)(kg): 2.5, Drive Method: [Slide Screws] Slide Screw + Belt, Guide: Included, Lead(mm): 16, Input Power Supply: DC 24V, Position Detection: Incremental, I/O Module: NPN, Table Width W1(mm): 60, Brake: Not Provided, Max. Thrust Force Range(N): 0 to 100, Max.
EX260-SEN_eng Resistance to ground should be 100 ohms or less. OFF The SI unit operating voltage is not supplied or the IP address is not set. 6 LED Bus statusspecific and SI unitspecific LEDs Green ON EtherNet/IPTM communications established. CAUTION indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury.
Mbps, half duplex 100 Mbps, full duplex 10 Mbps, half duplex 10 Mbps, full duplex OFF OFF OFF ON ON ON 3 : : Automatic Signal name Setting2 1 2 3 4 5 6 7 8 ON OFF OFF OFF ON ON ON RX+ RXSettings2 TX+ TX: : OFF OFF OFF ON ON ON : : (2) (3) Content OFF OFF OFF ON ON ON SI unit output data size 4 byte (Default setting) 6 : : OFF OFF OFF ON ON ON 1 2 3 4 5 6 7 8 7 8 1 byte 2 byte 3 byte : :
(It is recommended to ground with resistance of 100 ohms or less) M12 M12 10 14.9 Operation, Storage: 35 to 85%RH (No condensation) Operating humidity range : Seal cap is provided.
Resistance to ground should be 100 ohms or less. -14No.EX-OMV0023-A LED Indication and Settings LED indication LED Status Description OFF SI unit operating voltage is not supplied. POWERLINK communication has not been established.
Please keep this manual handy for future reference. 030 3 [m] Power supply for input and control is ON Green LED is ON Communication cable 050 5 [m] 100 10 [m] LED is OFF Communication error between GW unit has occurred COM Green LED is ON Communication between GW unit is normal LED is OFF Power supply for Solenoid valve is OFF PWR(V) L Green LED is ON Power supply for Solenoid valve is ON
When 1 digit = 1 kPa, the pressure is given with an increment of 1 kPa, e.g., 1, 2, 3, , 99, 100. Digit (Min. setting unit) E One of the switch output types, and means the operation in which a switch is turned on when pressure equal to the switch output set value or less is detected.
The time from when the flow is applied as a step input (when the flow rate changes from 0% to 100% instantaneously) until the analogue output (voltage) reaches 90% of the actual flow rate. Response time Ripple Indicates pulsation. T Temperature characteristic The amount of variation in the analogue output or display value when the ambient temperature is changed. -13No.
(with polarity protection) Power consumption 50 mA or less -50No.PF-OMN0005-E Model PFMV3 Enclosure IP40 Operating temp. range Operating: 0 to 50 oC; stored: -10 to 60 oC (no frezzing or condensation) Operating humidity range Operating and stored: 35 to 85% R.H.
(Note1) (Petroleum,Water-glycol, Emulsion,Phosphoric ester) Applicable model FH100-06 FH100-08 FH100-10 FH100-12 FH100-16 FH100-20 FH100-24 INOUT Port size (Rc) 3/4B 1B 1 1/4B 1 1/2B 2B 2 1/2B 3B Drain port size M162 Rated flow Paper 50 80 120 160 260 450 600 rate Micromesh 60 100 150 200 300 550 700 (L/min) Operating pressure 1.0MPa Operating temperature 80oC Nominal filtration 1.
W hite Blue COM +12V +12V Yellow COM n Brown +12V Red Built-in sensor power supply 12VDC, 60 mA Black .. Cable with shield 4-3 Noise countermeasures 1. Use SMC extension cable CE1-R** for wiring of MONOSASHI-KUN and CEU5. Follow the instructions below to prevent malfunction due to noise. 2. Keep signal wires away from the power cables in wiring. 3.
Do not use a cable longer than 100 m. Do not cut the lead wire between the sensor and amplifier. It may malfunction after connecting it again. Environment Pay attention to use the product in an atmosphere with accumulation of iron waste or close contact with magnetic substances.
Do not use a cable longer than 100 m. For long wire lengths, we recommend a ferrite core should be attached to both ends of the cable, to reduce noise. (2) Do not use a load which generates a surge voltage.
Polyurethane tube for piping 4 (TU0425BU-100) 2m.
Polyurethane tube for piping 4 (TU0425BU-100) 2m. Conversion cable 1pc. 4 2.