Electro-Pneumatic Positioner NIP600.NIP610 iop of lhe coupler as shown above.
Green flashing CAUTION indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Assembling the unit as a manifold (1)Connect a unit to the end plate. Digital and Analogue I/O units can be connected in any order. Tighten the joint brackets to a torque of 1.5 to 1.6 Nm. MS Normal operation. Diagnostic error is detected.
Turn cover A counterclockwise until it stops (approx. 45). 4. Install a new element on cover A and insert it into the case. Cover A Case Cover A Case O L L Element O-ring Window 5.
There is a risk of unexpected malfunction. Do not use solvents such as benzene, thinner etc. to clean each unit. They could damage the surface of the body and erase the markings on the body. Use a soft cloth to remove stains. For heavy stains, use a cloth soaked with diluted neutral detergent and fully squeezed, then wipe up the stains again with a dry cloth.
(Equivalent to M4) CAUTION indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: How to reset the product after a power cut or forcible de-energizing The setting of the product will be retained as it was before a power cut or deenergizing.
Ships as a "Kit" with S/S mounting screws 10. Installs easily in either Namur mounting position XO-RRD-2.5M SMC Corporation of America 10100 SMC Blvd.
How to reset the product after a power cut or forcible de-energizing The setting of the product will be retained as it was before a power cut or de-energizing. The output condition is also basically recovered to that before a power cut or de-energizing, but may change depending on the operating environment.
Enclosure Note) Impact resistance: No malfunction when tested with a drop tester in the axial direction and at a right angle to the main valve and armature, one time each in both energized and deenergized states.
And the title window will disappear in a few seconds, but it can be skipped by clicking on the title window. (The above title window of the setting software for JXC3 is the same as it for JXC2.) -4- The main window as shown below is then displayed. Communication status (The above main window of the setting software for JXC3 is the same as it for JXC2.)
Number of needle rotations 656 AS Series Speed Controller: Standard Type In-line Push Locking Type Construction Dimensions AS-F 61.5 (Max. 68.5) TMH ASD AS AS AS-FE 2 x 5.5 Component Parts No. Description Material KE Reference dimensions AS-FG 1 2 3 4 Body Valve Cap Needle Aluminum alloy NBR Rolled steel Brass POM Zinc alloy AS-FP AS-FM 5 Handle Replacement Parts AS-D No. Part no.
A B-1 A A-1 B B-2 B A-2 COM-A/COM B-3 COM-B/ A-3 Cable type Nil Robotic cable (Flexible cable) S Standard cable Cable color Connector D terminal no.
Space at manual release Leave a space in order to release by hitting with a plastic hammer. 150 Min.
The minimum stroke for auto switch mounting, operating range and auto switch mounting brackets/part no. are the same as standard products. For a cylinder with D, -B is suffixed to the end of the part number.
Process Valve VNB Series 2 Port Valve For Flow Control A wide variety of applicable fluids [Option] Proper selection with body and sealing materials permits application with a wide variety of fluids such as air, water, oil, gas and vacuum. Cylinder actuation by external pilot air Wide variations N.C., N.O., C.O., types are available.
D-F9WV D-F8 Model A B C D E A B C D E A B C D E A B C D E A B C D E A B C D E A B C D E A B C D E 18.5 31 6.5 20.5 41 8.5 20.5 33 4.5 17 20.5 31 4.5 15 20.5 41 4.5 15 20.5 51 4.5 35 22.5 43 6.5 27 22.5 33 6.5 17 22.5 43 6.5 27 22.5 53 6.5 37 MIW12-12D MIW20-20D 6 4 4 2 18.5 29 6.5 20.5 31 8.5 MIS12-10D MIS20-10D 4 2 6 4 2.5 4 18.5 39 6.5 20.5 41 8.5 MIS12-20D MIS20-20D 6 4
(Plugged when the product is not a symmetric type.) 17 12 5 37 43 3 +0.03 0 depth 1.5 17 11 17 A 14 2.5 3 2.5 3.5 A 4.8 4 x M3 x 0.5 3 +0.05 0 depth 1.5 A-A Other dimensions are the same as standard model (Series MXJ). 827 Air Slide Table 11-MXJ Dimensions Air Preparation Equipment Pressure Control Equipment Flow Control Equipment Pressure Switches/ Pressure Sensors Directional Control Valves
Caution Mounting 1) Do not subject the gauge to shocks, such as dropping during transportation and mounting, as this can cause loss of indication accuracy. 2) Do not use this gauge in a location with high temperature and humidity, as this may cause faulty operation. 3) When mounting the pressure gauge, be certain to use a wrench on the square wrench flats to screw it into place.
When using a cutter to remove the tubing, sufficient care should be taken so as not to make any flaws on the barb fitting. 5) After tubing installation, avoid excessive loads, such as tensile, compressive, or bending strength, being applied to the tubing.
This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switch-mode power supply and the product, or by using a series power supply instead of the switch-mode power supply.
Output numbers are assigned to side A and B alternatively. In case of single solenoid valve, output on side B is free. (Refer to Fig. a) : Mixed (single and double) wiring is available as long as wiring specifications designate it. This allows output numbers to be specified without having free output.