PVC Quick Drain Valve A watertight seal can be obtained by hand tightening. LVN Never use a pipe wrench etc., as it may break the product. Table 1 shows the tightening torque for reference. LQHB Table 1 Tightening Torque of Union Nut TL TIL 6.
*1 IN/OUT 5 M12 (4/5 pins) A-coded*1 IN/OUT * When the end plate (U side) is used, the symbol for the mounting method must be the same as the D side.
(Value in the initial stage) 3 position exhaust center 3 position exhaust center (B) 2 (A) 4 (B) 2 (A) 4 1 (P) 3 (R) 5 (R) 1 (P) 3 (R) 3 position pressure center 3 position pressure center How to Order Manifold Base Pilot Pressure Range (Single pilot) (B) 2 (A) 4 (B) 2 (A) 4 Uses the same manifold bases as the SYJ3000 series. 0.6 1 (P) 3 (R) 5 (R) 1 (P) 3 (R) SS5YJA3 The remainder part number
I I I I ~'" " I ~, 0-1 ~~ l'L Cross-section A-A' Parts List No. Design.?liOh .
Apply a tightening torque of 0.98 Nm or less. Rear piping ... Bracket A (Model: ZS-24-A) Bracket D (Model: ZS-24-D) Bottom piping ... Bracket B (Model: ZS-35-A) Hysteresis H_1 WARNING indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury.
As a result, the air supply valve @ linked to the diaphragm @ opens, and a portion of the supply pressure becomes output pressure. This output pressure feeds back to the control circuit via the pressure sensor O.
None K Lock Nut Hexagonal Width across Flat (Special Order) N Nickel Plating A R E A C O D E Ambient and Fluid Temp 0 ~ 60OC / 32 ~ 140F ...
In the case of ZNR surge voltage suppressor, take note the surge voltage to be suppressed at controller side as there will be a residual voltage according to the protective element and rated voltage. Moreover, the residual voltage of the diode is approximately 1V. 647 A
This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switch-mode power supply and the product, or by using a series power supply instead of a switch-mode power supply. Selects the mode or increases the ON/OFF set value. Press this button to change to the peak display mode. button (UP) [F 4] [F 5] [F 6] [F 7] [F 8] [F 9] [Anr.]
(See point A on the graph for Series LJ1H30.) Since point A is above the line for 18kg, a regenerative absorption unit is required. 1 8kg 100 20kg 50 0 100 200 Stroke (mm) 300 400 500 600 Danger Consult P/A if the connected controller power supply voltage is 220VAC, as this may cause fire or malfunction. 203
Detaching To detach a socket from a connector, pull out the lead wire while pressing the sockets hook with a stick having a thin tip (about 1 mm). If the socket will be used again, first spread the hook outward.
As shown in the below figure, mount a crimped terminal (9), and then again tighten the screw (3e). Note) Tighten within the tightening torque of 0.5 Nm 15%. Note: a It is possible to wire even in the state of bare wire.
It is expressed as a percentage of the full-scale value of the reading according to the type of instrument. E ZSE ISE Ejector Simple piece of equipment to generate a vacuum. Positive air pressure is used to generate a vacuum. No moving parts. Analog output function A voltage or current output which has a value proportional to the measured pressure.
There is a risk of unexpected malfunction. Do not use solvents such as benzene, thinner etc. to clean each unit. They could damage the surface of the body and erase the markings on the body. Use a soft cloth to remove stains. For heavy stains, use a cloth soaked with diluted neutral detergent and fully squeezed, then wipe up the stains again with a dry cloth.
DANGER indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Danger: Maintenance Switch ON At normal output Switch OFF M3x5 L M3x5 L M3x5 L Time [s] How to reset the product after a power cut or forcible de-energizing The setting of the product will be retained as it was before a power cut or de-energizing.
The minimum pressure can be set as low as 0% and as high as 50% of the full span. The maximum pressure can be set as low as 10% and as high as 100% of the full span. For example, an ITV203 could be set to output 35 PSI at 0% input signal, and 43 PSI at 100% input signal (there must be at least 8 PSI separation).
Part A should then be pressed in using a suitable tool, such as pliers. The e-con connector cannot be re-used once it has been fully crimped. In cases of connection failure such as incorrect order of wires or incomplete insertion, please use a new connector.
(When diagnostic parameter is enabled) CAUTION indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Assembling the unit as a manifold (1)Connect a unit to the end plate. Digital and Analogue I/O units can be connected in any order. Tighten the joint brackets to a torque of 1.5 to 1.6 Nm.
There is a risk of unexpected malfunction. Do not use solvents such as benzene, thinner etc. to clean each unit. They could damage the surface of the body and erase the markings on the body. Use a soft cloth to remove stains. For heavy stains, use a cloth soaked with diluted neutral detergent and fully squeezed, then wipe up the stains again with a dry cloth.