SGC200-OMJ0004 Rc1/4 1214 Rc3/8 2224 Rc1/2 2830 Rc3/4 4550 Rc1 6570 , , , , 1.5~2 1) 2) 3) 2 5 SGC200*-OMJ0004-A SGC/SGH Series SGC/SGH Series SGC/SGH Series SGC/SGH Series 2 2 2 2 / / / / 30 1 1) 2)1 0.1MPa 3)0.1MPa 2 2 2 2 6 SGC200*-OMJ0004-A SGC/SGH Series SGC/SGH Series SGC/SGH Series SGC/SGH Series/ / / / 1 DC AC VT307 C-R ( ) C-R DC 3% AC 8% [ [ [ [ ] ] ] ] (90) D () [:0.1Nm ] D ,, 7
Pressure Breathing Breathing Operate after confirming the compatibility of the product's com ponent materials with fluids, using the check list on page 7. Please contact SMC regarding fluids other than those in the check list. Operate within the indicated fluid temperature range. N.O. Breathing Pressure Breathing Double acting Pressure Pressure Breathing 3.
Construction Auto switch (Optional) Bonnet assembly (Maintenance part) (Including 3, 7, 9, and 10) Indicator (Optional) 1 Magnet (Optional) Pilot port Cylinder Bellows holder (Material: SUS304) 8 Heater (Optional) External seal (Maintenance part) 4 Shaft (Material: SUS304) 10 Bellows assembly (Maintenance part) (Including 2, 6, and 8) Bellows (Material: SUS316L) 7 Valve seal 1 (Maintenance
Specifications 7 4. Construction and Outer dimensions --9 5. Period and scope of warranty 10 6. Parts replacement procedure 11 1 XL*-OML0013-B Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Note4) Figures in ( ) indicates the mass of CF (conflate) fittings. 7 XM-OMP0002-A 4. Construction / Dimensions 4-1.
JMHZ2-16D-X7400B-ASSISTA(-P) mm 16 MPa 0.1~0.7 (oC) -10~50 (mm) 0.01 (c.p.m.) 120 32.7 (N) 43.5 (mm) 10 (g) 680 D-M9(N/P)-5 ISO9409-1-31.5-4-M5 (www.smcworld.com)JMHZ2 Series P .15 M12 8 6 - 3-2. 2 1 F 7 - 3-3. H 8 - 3-4. () P11P12P13 8 8 4 27 17 9 - 3-5. M12 8 () PIN 1 GND DC0V 2 +24V DC24V 3 ON/OFF 4 ON/OFF 5 6 7 8 3-6.
accessory 6 Parallel inputPNP) 1 I/O cable1.5m Parallel inputNPN) Parallel inputPNP) E EtherCAT 3 I/O cable3m 9 EtherNet/IP 5 I/O cable5m P PROFINET Controller mounting 7 Screw mounting Single axis 8*1 DIN rail /High performance *1 The DIN rail is not included.
(If motor option With lock was selected lock cable is included too.) 11-LEFS40 11-LEFS40 7 - Construction 11-LEFS No. Description Material Remarks No.
(At 15m: Reduced by up to 20%) 5) The allowable speed for the pushing operation. 6) A reference value for correcting an error in reciprocal operation 7) Impact resistance: No malfunction occurred when it was tested with a drop tester in both an axial direction and a perpendicular direction to the lead screw. (The test was performed with the electric actuator in the initial state.)
Maintenance 78 7. Countermeasures for Failure 9 8. Spare Parts List 10 9. Drawings 11 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Check the connector between the SI unit and solenoid valve manifold for a connection failure, such as a bent pin 7 Solenoid valve malfunction.
At the same time, the auto switch will be damaged. 7. Avoid incorrect wiring. 1) If connections are reversed on a 2-wire type auto switch, the auto switch will not be damaged if protected by a protection circuit, but the auto switch will always stay in an ON state.
Solenoid valve failure 7 Solenoid valve malfunction Connection between SI unit and valve manifold is defective Check that there is no contact failure such as bending of the connector pins between the SI unit and valve manifold Connect the SI unit and valve manifold properly.
Note 3) Air consumed by a reciprocating motion of a cylinder. 7 XL*-OMJ0003-D 3-2. Heater specifications Item XL-25 XL-40 XL-50 XL-63 Rated voltage of the heater 90 to 240 ACV Heater assembly number XLA25-60S-1 XLA25-60S-1 XLA25-60S-2 No. of heater assemblies 1 pc. 1 pc. 1 pc.
When setting, allow 7 digits or more between Set point 1 and Set point 2 (Set point 3 and Set point 4). 2: When Set point 1 = Set point 2 (Set point 3 = Set point 4), chattering may occur. -21No.PF-OMO0012-E Initialize mode Default settings Item Default settings Page Selection of display mode [d_1] Display instantaneous flow Unit selection function [U_1] L/min Page 23 Selection of output
Refer to Glossary of Terms on page 6 for detail of max. operating pressure differential and max. system pressure. 10 Select an option mark in page 7 by Applicable Fluids Check List for special fluids outside of the standard.
Mounting backward is dangerous, because the speed adjustment needle will not work and the actuator may lurch suddenly. (7)Adjust the speed by opening the needle (2)Products mentioned in this catalog are not designed for use as stop valves with zero air leakage. A certain amount of leakage is allowed in the products specifications.
(Tightening torque 0.6 to 0.8Nm) Dipswitch ON 1 2 1 2 3 4 5 6 7 8 9 10 SW40 SW20 SW10 SW08 SW04 SW02 SW01 BS4 BS2 BS1 Hold/Clear Terminating resistor Setting at the time of shipment 1 2 1 2 3 4 5 6 7 8 9 10 Node address: 1 Baud rate: 10Mbps Hold/Clear: Clear Terminating resistor: disable Setting of node address Node address SW40 SW20 SW10 SW08 SW04 SW02 SW01 1 OFF OFF OFF OFF OFF OFF ON 2
For details, refer to the WEB catalog or Best Pneumatics No. 3. 15-E649 Series MGP Series MGP Dimensions: 12 to 100 With Flange MGPF Flange FC FD H G FF FE 4 x FG through B + Stroke C + Stroke FB FA FH [mm] Bore size B C FA FB FC FD FE FF FG FH G H 12 42 29 7 6 80 89 18 25 4.5 5 26 58 16 46 33 7 6 88 98 22 32 5.5 5 30 64 20 53 37 8 8 102 112 24 38 5.5 6 36 83 25 53.5 37.5 9 7 114 126 30
MTS 4.11-6 Standard MTS SMTSl 4.11-6 With end lock MTSR 5.5-3 Copper-free Actuators SMC Actuator 6, 8, 10, 12, 15, 16, 20, 25, 32, 40, 50, 63, 80, 100, 125, 140, 160 Air Cylinder Series Application Bore size (mm) Name of CAD file Page in Vol.2 Standard Copper-free 6 8 12 (10) 16 (15) 20 25 32 40 50 63 80 100 125 140 160 Series/Variation Mechanical joint rodless cylinder Series MY1 3.23-7