Vacuum Equipment

If the leakage volume is 5 /min (ANR), the vacuum pressure of the S type is 80 kPa r t y, and for the L type it is 47 kPa r' t' y'. Thus, if the leakage volume is 30 /min (ANR) the L type can attain a higher vacuum pressure, and if the leakage volume is 5 /min (ANR), the S type can attain a higher vacuum pressure.

2–4

Although a zener diode for surge protection is connected at the output side of a solid state auto switch, damage may still occur if a surge is applied repeatedly. When directly driving a load which generates surge, such as a relay or solenoid valve, use a type of switch with a built-in surge absorbing element. 8.

PA3000/5000/PAX1000

Since a large quantity of liquid will be pumped out, use a suitable throttle in the discharge port if problems occur. Note 3) With a low number of operating cycles, even a valve with a small Cv factor can be operated.

SY3000/5000/7000 Series Plug-in Type

Leakage voltage Take note that the leakage voltage will increase when a resistor is used in parallel with switching element or a C-R circuit (surge voltage suppressor) is used for protecting a switching device because of the passing leakage voltage through the C-R circuit. The suppressor residual leakage voltage should be 3% or less of the rated voltage. 6.

CUJ

Refer to page 2. 11 3.5 2-M3 x 0.5 (port size) M3 x 0.5 (Relief port: 10 See above) (Vacuum port: 11 See above) 3.5 3 C + Stroke B + Stroke A + Stroke (mm) Without auto switch With auto switch A B C A B C Bore size (mm) 24 18 29 23 11.5 16.5 6, 8, 10 4 Series CUJ Construction Double acting !3 w e q !1 r y o e t !2 For 4 Built-in magnet Without magnet Single acting u i r y o e w i e u !

Process Pump Series PA3000/5000/PAX1000 Series PB1000

Since a large quantity of liquid will be pumped out, use a suitable throttle in the discharge port if problems occur. Note 3) With a low number of operating cycles, even a valve with a small Cv factor can be operated.

Process Pump Series PA3000/5000/PAX1000 Series PB1000

Since a large quantity of liquid will be pumped out, use a suitable throttle in the discharge port if problems occur. Note 3) With a low number of operating cycles, even a valve with a small Cv factor can be operated.

25

Avoid using in a place that exceeds an ambient temperature range. b. Avoid using in a place that exceeds an ambient humidity range. c. Avoid using in a place where condensation occurs due to a drastic temperature change. d. Avoid using in a place in the presence of corrosive or explosive gas or where there is a volatile combustible. e.

Process Pump

(A) 2 23 (AR) (A) 2 Refer to Best Pneumatics No. 1 for further details. 3 (R) 1 (P) 3 (R) 1 (P) Regulator Series AR Model Specifications Model AR20 Port size 1/8, 1/4 AR25 1/4, 3/8 AR30 1/4, 3/8 AR40 AR20 AR25 AR30 AR40 Model Proof pressure 1.5 MPa 1.0 MPa 0.05 to 0.85 MPa 1/4, 3/8, 1/2 Max. operating pressure Pressure gauge port size 1/8 1/4 Set pressure range Ambient and 5 to 60C (No freezing

LFE-OMZ0012

1/2(15 A) 3/4(20 A) 1(25 A) Weight(Body) *5 Approx.

CE2

Cover Rod cover Unit holding tie-rod A (2 depth 1 mm hole is on the side of tie-rod for attaching unit A.)

CEx-OMG0106

At piping This is equivalent to a magnetic field of approximately 18cm in radius from a welding area using a welding current of almost 15,000 amperes. To use the system in a magnetic field that exceeds this value, use a magnetic material to shield the sensor unit Foreign matter should not enter. Entering of foreign matter will cause malfunction.

Vacuum Pad: Large/Heavy Duty Type Series ZPT/ZPX

B D A A B D B D Dimensions (mm) Dimensions (mm) Dimensions (mm) A B C D E F Y A B C D E F G Y A B C D E F Y Model Model Model ZP40HB ZP63HB ZP100HB 40 41 28 43 20.5 30 13 63 65 46 68 31.5 50 4.5 21.5 100 103 69 107 47.5 80 35.5 ZP125HB ZP50HB ZP80HB 50 52 36 54 24 40.5 16.5 80 83 58 85 37 64 5 27.5 125 129 89 135 56 105 44 1213 Series ZPT/ZPX How to Distinguish Different Pad Materials How

Compact and Lightweight

Set of long clamping screws ZH2-TB203-A 3 M4 x 70 2 pcs. ZH13DA ZH15DA ZH2-TB204-A 4 M4 x 90 2 pcs. ZH2-TB206-A 6 M4 x 130 2 pcs. Hexagon nut (M4) 2 pcs. ZH2-TB208-A 8 M4 x 170 2 pcs. (ZH2-TB201-A)3 1 M4 x 30 2 pcs. Flat washer (for M4) 2 pcs. ZH2-TB302-A 2 M4 x 55 2 pcs. ZH2-TB303-A 3 M4 x 80 2 pcs. ZH18DA ZH20DA ZH2-TB304-A 4 M4 x 100 2 pcs. ZH2-TB306-A 6 M4 x 145 2 pcs.

Hydraulic Cylinder 7MPa Nominal Pressure Series CHN

P/A as a contact protection box may be necessary.

Digital Gap Checker

Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.

Ｍ agnet Gripper Unit for Collaborative Robots

Devise a safe system so that if a person engages the emergency stop or if a safety device is tripped during a system malfunction,such as a power outage, the operation of the magnet gripper will not cause a hazard to humans or damage the equipment. 7. Consider the action when operation is restarted after an emergency or abnormal stop.

REC

cable O.D.: 6.8 to 11.5) CE1 CE2 Proper Auto Switch Mounting Position D-H7 D-H7C D-H7NF D-H7W D-H7BAL D-C7 D-C80 D-C73C D-C80C ML2B D-G39 D-K39 D-A33/A34 D-A44 D-B5 D-B64 D-B59W D-G5NTL Bore size (mm) C J G5-S A B A B A B A B A B A B CV 20 56.0 31.5 50.0 25.5 55.0 30.5 51.5 27.0 53.0 28.5 49.5 25.0 25 MVGQ 56.0 31.5 50.0 25.5 55.0 30.5 51.5 27.0 53.0 28.5 49.5 25.0 32 59.5 36.5 53.5 30.5

Gun Type Ionizer

After blowing, make sure to hang the product on a hook, etc. Caution 1. Clean specification is not available with this product. When using in a clean room environment, confirm the required cleanliness before use. A minute amount of particles are generated due to wearing of the emitters while the product is operating. Wiring / Piping Warning 1.

Clamp Cylinder with Lock Series CLK1

17 17 40 A 20 20 15 45 60 25 45 60 A Applicable clamp cylinder A Applicable clamp cylinder Part no.