Pressure Sensor Controller Do not use the product in a place where temperature suddenly changes even if it stays within the specified range. Do not expose the product to heat radiation from a heat source located nearby. It can cause malfunction. -6No.PS-OMG0002-G Adjustment and Operation Do not short-circuit the load. Do not press the buttons with a sharp object. It can cause damage to the setting buttons.
Operating conditions Warning (1) Do not use in an atmosphere containing corrosive gases, chemicals, sea water, water, steam, or where there is direct contact with any of these. (2) Do not expose the product to direct sunlight for an extended period of time. (3) Do not use in a place subject to heavy vibration and/or shock. (4) Do not mount the product in locations where it is exposed to radiant
not occur on the product of the cooling method -W. 2: These alarms do not occur on the product of the power specification '-20'.
Do not use pressure sensors with corrosive and/or flammable gases or liquids. 4. Connection of sensor connector Cut the sensor cable as illustrated to the right. Referring to the table below, insert each lead wire of the cable at the position marked with a number corresponding to 1.
Do not use exceeding the value shown by the graph.
PV SV 16. Select data length (simple communication protocol) from the table below with [] key or [] key, and confirm by pressing SEL.
Do not use in a place where water, oil or chemicals splashes. Otherwise it can cause failure or malfunction. Do not use the Pressure switch nearby a place where electric surges are generated.
Hold/Release success: default output DO[101] Hold/Release failure: default output DO[102] * Digital output port can be selected within DO[101] to DO[112] * you select the same digital output port for different status signals, a warning message will be displayed. 2. Test run The manual operation of the magnet gripper unit can be checked.
It may cause injury to personnel. 5) Do not use the product to clean or remove toxic substances or chemicals. 6) Do not drop, step on or hit the product.
Do not use in these conditions. (Refer to specifications.) Consult SMC if a fluid other than compressed air is used. 2.
For type W, DC voltage is only 5 16" One-touch fitting for N9 5 5 16" One-touch fitting for N9 One-touch fitting for One-touch fitting for One-touch fitting for available.
Do not use in locations where static electric charges will be a problem. Consult SMC regarding use in this kind of environment. 6. Do not use in locations where spatter occurs. There is a danger of spatter causing a fire.
Do not use in locations where static electric charges will be a problem. Consult SMC regarding use in this kind of environment. 6. Do not use in locations where spatter occurs. There is a danger of spatter causing a fire.
through until it comes out the other side. 4) Do not get across steps with casters.
Do not drop or bump. Do not drop, bump or apply excessive impacts (300m/s or more for reed switches and 1000m/s or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.
Do not mount the product in locations where it is exposed to radiant heat. 5. Do not use in dusty locations or where water, oil, etc., splash on the equipment. 6.
Failure to do so may cause equipment failure or malfunction. 9. Mount the Fieldbus system in a location where there is no excessive vibration or shock. Failure to do so may cause equipment failure or malfunction. 10. Do not use in places where there are cyclic temperature changes.
I" = 2. 4. 6. 8.. ) (n = 4.8, 12. 16") (n = 4, 8, 12. 16 .. ) (n = 4, 8, '2, 16 ..) With 2 pes. (DiUerent surfaCfls 115 20 120 ' 25 Same surface), With 1 pc (n '" 2. 4. 6, 8.. ~_-L_("":.:=,, 4 "2 ' :0 .. ,1 _ (" ,,.-,,8,-.' ' :0.. ) ".-,,. ' "2,,.-,-"." ) ,,.-,,8,-.' ,,.,,6.")
22 K 46 58 68 FF 63.5 77.5 95 L 45.5 54 64 GG 22 27 35 M 30.9 32.4 41.4 HH 24 32 37 N 16 15 19 O 69 84 102 P 41 56 68 CC 16 19 23 BB 30 35 40 AA 106 133 164 B 220 280 340 C 206 264 322 D 42 51 59 E 138 168 204 F 93.5 107.5 130.5 II 16 19 23 I 76.5 91 110 Model ML2B25 ML2B32 ML2B40 MM 16 21.5 24.5 MA M5 x 0.8 M6 x 1 M8 x 1.25 NN 22 26 37.5 LC 9.5 12 12 LB 9.5 16 15 LD 5.5 6.5 8.5 MC M5 x
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate or set with wet hands. This may lead to an electric shock. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.