ZISE10.eng Claw 1 Claw 2 Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Error Name Error Display Error Type Troubleshooting Method [2] Turn the power off and remove the output factor for the over current. Then turn the power on.
Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. This function is to display error location and content when a problem or an error occurs. Error name Error display Error type Troubleshooting method Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids.
Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Preparation before setting (1)Supply pressure to the product. (2)Place the workpiece on the detection nozzle. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
the operating conditions to calculate the product life, and do not exceed it.
Our pressure switches do not have an explosion proof rating. Never use in the presence of an explosive gas as this may cause a serious explosion. 3. Do not use in an environment where static electricity can cause problems, otherwise system failure or malfunction may result. 1. Do not drop, bump, or apply excessive impacts (980 m/s2) while handling.
Do not use in atmospheres where the valve is in direct contact with corrosive gases, chemicals, salt water, water or steam. 2. Do not use in an explosive atmosphere. 3. Do not use in locations subject to vibration or impact. Confirm the specifications in the main section of the catalog. 4. Use a protective cover, etc., to shield valves from direct sunlight. 5.
Do not lift the product by holding the panel, fittings or piping. Never lay the product down for transportation. This may lead to damage to the product. A polyurethane tube is attached as a drain tube for this product. Use this tube to discharge drainage to a drain tank etc. Do not use the drain tube in an upward direction. Do not bend or crush the drain tube.
Do not operate with the magnetic coupling out of position. If the magnetic coupling is out of position, push the external slider by hand (or the piston slider with air pressure) back to the proper position at the stroke end. 3. Do not apply a lateral load to the external slider.
In a locked state, do not apply impacts, strong vibrations or rotational forces. Do not apply a impacts, strong vibrations or rotational forces from external sources, because this could damage or shorten the life of the lock unit. 4. The locking of the fine lock cylinder is directional.
Piping Caution Caution Handling 1.Do not inadvertently move the guide adjusting unit. The guide is installed at the proper tightening torque. Do not loosen the mounting bolts of the guide. 2.Do not operate the magnetic rodless cylinder if the magnet couplings on the actuator are displaced.
The set screws in the figure below are for securing the guide shaft, so do not loosen them except for the purposes of replacing the seals. This can cause a malfunction. Caution 1. Do not use the cylinder in an environment where the cylinder is expose to moisture, adhesive foreign matter, dust or liquid such as water or cutting fluid.
A B High precision type Basic type Port location Nil E Side ported Front ported Size 1 2 3 7 A With adjustment bolt Dimensions Clean series products do not have a hollow axis.
Do not install it by directly grasping the piston rod with a pair of electricians pliers.
When installing the cylinder into equipment or performing adjustments, etc., be sure to apply air pressure of 0.25 MPa or more to the unlocking port, and do not perform work using the unlocking cam. 3.
Do not operate the CS1 series at twice the output. Applicable Series Series Description Note Vol. no.
Prevention of electric shocks and fire Do not operate the switch with wet hands. Also, do not operate the thermo-con when water is present on its exterior surface. 2. Action in the case of error If any error such as an abnormal sound, smoke, or bad odor occurs, cut off the power at once, and stop supplying and conveying fluid.
Do not cover the inlet and outlet vents.
Do not use the drain tube in an upward direction. Do not bend or crush the drain tube. (Operation of the auto drain will stop water vapor from discharging through the air outlet.) If it is unavoidable that the tube goes upwards, make sure it only goes as far as the position of the auto drain. Power Supply Caution Connect the power supply to the terminal block.
Do not use the drain tube in an upward direction. Do not bend or crush the drain tube. (The auto drain will not be activated and water will try to escape via the air outlet.) If it is necessary that the tube goes upwards, make sure it only goes as far as the position of the auto drain.
Do not use the product where these are present. 2. Applications in which the difference between the inlet and outlet pressure exceeds 0.1 MPa must be avoided. Failure to do so may result in element breakage. 3. For air blow applications, prevent airborne particles from the operating environment from entering into the compressed air stream.