M-E06-4-LQ3 ) 03 (3, 1/8"), 04 (4), 06 (6), 07 (1/4") only Table 1 Tubing Size Symbol Metric size Inch size Tubing O.D. 3 03 4 04 6 06 8 08 10 10 12 12 19 19 25 25 1/8" 03 1/4" 07 3/8" 11 1/2" 13 3/4" 19 1" 25 Symbol Note 1) GPS GB GB GPS Fitting type Note 1) Sizes with the same symbol number and 06 and 07 are common sizes. 6 c Akihabara UDX 15F, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021, JAPAN
Additionally, do not put the tube end in the liquid. This may cause the back pressure to be applied, resulting in poor performance. 3.Liquids cannot be collected by the air. 1076 A
Note) Do not apply rotational torque to the piston rod. q MK/MK2 RSQ/RSG Connect the shield wire to FG (frame ground).
Do not use valves in atmospheres of corrosive gases, chemicals, salt water, water, steam, or where there is direct contact with any of these. 2. Products compliant with IP65 and IP67 enclosures (Based on IEC529) are protected against dust and water, however, these products cannot be used in water. 3.
Brazil SMC Pneumaticos Do Brasil Ltda. Venezuela SMC NEUMATICA VENEZUELA S.A. Chile SMC Pneumatics(Chile) S.A. Bolivia SMC Pneumatics Bolivia S.R.L. Uruguay BACO S.A.(Distributor) Colombia Airmatic Ltda.(Distributor) Peru IMPECO Automatizacin Industrial S.A.(Distributor) 9 U.K SMC Pneumatics (U.K) Ltd. Germany SMC Pneumatik GmbH China SMC (China) Co.,Ltd.
Do not attempt to rotate, as it does not turn Cable connection threads RC(PT) 1/4 Exhaust porl EXH (3) Port size 4-M5 x 0 8 thread depth 6mm Mounting hole 2-RC(PT) 1/4, 3/8 SUP port, OUT porl rTl|z000/3000 tleflru-Pltotllnalic Re[ula 0imeffiiolt$ ITV3OtrT Cable connector (4 wire) Cable connector (4 wire) . Do not anempt to rotate. as it does not turn.
Do not service or attempt to remove product and machinery/ equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.
Tool required) C: Locking type (Lever) Body size 20 30 40 50 1/4 3/8 1/2 3/4,1 Thread type Rc G NPT Nil F N Light/Surge voltage suppressor None Nil S Z With surge voltage suppressor (Grommet type only) With light/surge voltage suppressor (Not possible with grommet type) Port size Electrical entry 1/4 (AV2000 only) 3/8 (AV3000 only) 1/2 (AV4000 only) 3/4 (AV5000 only) 1 (AV5000 only) 02 03 04
The allowable voltage uctuation is 15% to +5% of the rated voltage for the 115 VAC or 230 VAC. *2 Type Y is a DIN terminal conforming to EN-175301-803C (former DIN43650C). *3 When the electrical entry is DO or YO, light/surge voltage suppressor cannot be selected. *4 Only for the NPT thread Option: Select one each for a to c.
Option 1 External pilot solenoid 2 Internal pilot solenoid Nil None Thread type Nil Rc F G N NPT T NPTF Body size Port size B Bracket (VEX312 only) Body size Port size Port 1(P), 2(A), 3(R) 12 01 1/8 02 1/4 Rated voltage VEX312 VEX332 1 100 VAC (50/60 Hz) 2 200 VAC (50/60 Hz) 3 110 VAC (50/60 Hz) 4 220 VAC (50/60 Hz) 5 24 VDC 6 12 VDC V 6 VDC S 5 VDC R 3 VDC * DC specification of type D and DO
How to Order B LG1 02 1 Cable length 02 03 04 05 2m 3m 4m 5m Nonstandard Motor Cables Cables for connecting nonstandard motors and drivers. Cable lengths other than those shown below should be arranged by the customer.
Do not allow the weight of piping to lie directly on air dryer. 4. Do not connect a tube smaller than the port size to the inlet side. In particular, when using a resin tube, make sure that the size would not be smaller than the port size.
NTJ-015A NT-02 NT-04 NT-05 12 M5 x 0.8 4 8 9.2 7.8 H B 20 M8 x 1.25 5 13 15.0 12.5 32 . 40 M14 x 1.5 8 22 25.4 21.0 50 . 63 M18 x 1.5 11 27 31.2 26 Electrical Wiring Output type The output signal of the stroke reading cylinder is A/B phase difference output (open collector output) as shown in the figure below.
Do not apply external force to the coil section. When tightening is performed, apply a wrench or other tool to the outside of the piping connection parts. 2. Do not warm the coil assembly with a heat insulator, etc. Use tape, heaters, etc., for freeze prevention on the piping and body only. They can cause the coil to burn out. 3.
The received message is deleted if the calculation result and received LRC do not match. Add up the byte number of the message consisting of 8 consecutive bits. The result except the carry (overflow) is converted to 2s complement.
Since PE port is the exhaust port of the pilot valve, do not attach a plug or reduce the port diameter. 2. X port is the pressure supply port of the pilot valve and PE port is the exhaust port of the pilot valve. Avoid mismatching when piping. 3. The manual portion contains a breather hole for the core.
Since PE port is the exhaust port of the pilot valve, do not attach a plug or reduce the port diameter. 2. X port is the pressure supply port of the pilot valve and PE port is the exhaust port of the pilot valve. Avoid mismatching when piping. 3. The manual portion contains a breather hole for the core.
Cylinder Speed Chart Bore size Series CJ2 Pressure 0.5 MPa Load factor 50% Stroke 60 mm Series CM2 Pressure 0.5 MPa Load factor 50% Stroke 300 mm Average speed (mm/s) Series 6 10 16 20 25 32 40 800 700 600 500 400 300 200 100 Perpendicular, upward actuation Horizontal actuation VK VZ1120--M5 (Piping: 4 x 1 m) VZ VF AS1301F-M5-04/AN120M5 AS1301F-M5-04/AN120-M5 Speed controller/Silencer VFR