Title not found be) a a a a o a a a a a a a a a a a a a a a a a a a a a o a a a a a a o a a a a a a a a a o a a a a o a a a a a a o a a a a a a a Polyurethane Tirbing TIUB (lnch) TU TU EE4 si.. (..) J @ 1." roll T Length per roll 20nr 33mB"l 100m is3!
, d e t e r i o r a t i o n o f a c c u r a c y, a n d breakage of parts.)
-Pad ;;rol2 25 40 Flat type I a o o o a o a o o a o o Flat with rblo o a o o a a o eep tvpe lo a o a Bellows | a a a a a a o a a a 132 ZCDUKC Male Cap porting zPf (v&uum pad !
-Pad ;;rol2 25 40 Flat type I a o o o a o a o o a o o Flat with rblo o a o o a a o eep tvpe lo a o a Bellows | a a a a a a o a a a 132 I ZCDUKC Male Cap porting zPf (v&uum pad !
Operating principle A + A' A' A Piston seal A' A' R H R H When the piston is retracting, air is exhausted through both A and A' until piston seal H passes air passage A. After piston seal H has passed air passage A, air is exhausted only through A'. The section marked with slanted lines becomes a cushion chamber, and an air cushion effect is achieved.
(RES) A.10 Undervoltage A.12 Memory error 1 (RAM) A.13 Clock error A.15 Memory error 2 (EEP-ROM) A.16 Encoder initial communication error1 A.17 Board error A.19 Memory error 3 (Flash-ROM) A.1A Motor combination error A.1C Software combination error A.1E Encoder initial communication error 2 A.1F Encoder initial communication error 3 A.20 Encoder normal communication error 1 A.21 Encoder normal
Therefore, do not use a cylinder without a bumper bolt. Furthermore, if the bumper bolt is tightened without a nut, the piston seal is caught in the leveled part, damaging the seal. 3. A bumper at the end of the bumper bolt is replaceable. In case a missing bumper, or a bumper has a permanent settling, use a following part numbers for ordering.
1 E-P HYREG Series VY1 A hybrid regulator is created from a regulator and a solenoid valve F.R.L. AV AU Stepless control through electric signals AF A maximum effective area of 670 mm2 (2B) can be covered by the combination of an ultra-compact electro-pneumatic pilot valve (22.4 x 30 x 39) and a 3 port, high-capacity exhaust main regulator (Series VEX100).
At piping This is equivalent to a magnetic field of approximately 18cm in radius from a welding area using a welding current of almost 15,000 amperes. To use the system in a magnetic field that exceeds this value, use a magnetic material to shield the sensor unit Foreign matter should not enter. Entering of foreign matter will cause malfunction.
t r r , " . . a : r i . . . , r i a , r . .
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
t r r , " . . a : r i . . . , r i a , r . .
ZX B B' A B ZR A B P1 A A' ZM !0 o r t ZH ZU Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com e ZL ZY ZQ ZF ZP !1 ZCU Section A-A' (Ejector) AMJ !
When tightening the auto switch mounting screw, use a watchmakers screw driver with a handle diameter of about 5 to 6mm. Furthermore, use a tightening torque of 0.05 to 0.1 Nm. As a rule, it should be turned about 90 from the point at which tightening can be felt. Use a tightening torque of 1 to 1.2 Nm for the hexagon socket head set screws (M4 x 0.7). 1.
L32 pin clamp cylinder available O Compact design makes it applicable to a broad range of workpieces. OContributes to a lightweight jig.
8 A 8.1 8.2 A (10) 8.3 8.4 IDF60-20-A IDF60-30-A IDF70-20-A IDF70-30-A IDF80-20-A IDF80-30-A IDF90-20-A IDF90-30-A 50Hz 2.3 4 5.8 7.1 3/min(ANR) m 60Hz 3.2 4.8 6.5 7.9 10 1) ANR 65% 2) IDF60/70/80/90 Series 8-1 IDX-OM-W093 A 8.5 IDF60/70/80/90 Series 8-2 IDX-OM-W093 C 9 C 9.1 9.2 1) 2) IDF60/70/80/90 Series 9-1 IDX-OM-W093 A IDF60/70/80/90 Series 9-2 IDX-OM-W093 L 10 L L
As a guide, tighten it by hand, then turn it two or three turns with a wrench. Check the dimensions of each product for the hexagon width across flats.
D2 M1 L1 L2 T M5 type H (width across flats) Applicable tubing O.D. d A A4 D1 L3 D2 M1 L1 T L2 Model Weight (g) Note 2) Tubing O.D. d T H D1 D2 L1 L2 L3 M1 L4 Max.