Series MXP Precision Air Slide Table L=100mm L=100mm MXP10-10 MXP10-20 MXP10-10 MXP10-20 0.04 0.03 0.08 MXP10-10 MXP10-20 MXP10-10 MXP10-20 MXP10-10 MXP10-20 MXP10-10 MXP10-20 Table deflection (mm) Table deflection (mm) Table deflection (mm) 0.03 0.06 0.02 0.02 0.04 0.01 0.01 0.02 0 0 0 80 20 40 60 80 Load (N) 20 40 60 80 Load (N) 20 40 60 100 Load (N) 12 12 12 L=100mm L=100mm L=100mm MXP12-15 MXP12-25 MXP12-15 MXP12-25 0.05
20 191 11 20 50 98 70 44.5 16 84 11 6.4 117.5 316 3.3 280 46 20 196 20 11 50 70 98 44.5 84 13 11 6.4 117.5 319 3.3 Note 1) For AC20 only, the position of the pressure gauge is above the center of the piping.
As a result, it will not be possible to verify it with the vacuum switch. In such a case, it is necessary to use an ejector that is suited to the nozzle and to select a vacuum switch with a favorable hysteresis and precision. 3.
Also, do not use excessive power supply voltage or superimpose electrical noise such as ripple voltage on the power supply voltage as these could harm the valve. 5. When connecting an induction load such as a circuit protector to the solenoid valve connection, take measures to ensure that the current to the solenoid valve is not reduced too much.
Set the operating pressure using the graphs as a guide.
When removing drain is difficult, use of a filter with an auto drain is recommended. ITVX PVQ VY1 VBA VBAT AP100 3. Piping materials without flexibility such as steel tube piping are prone to be effected by excess moment load and vibration from the piping side. Use flexible tubing in between to avoid such an effect. Caution 1.
Model vEA 250/130 Basic type having driving function only w 251 As a system satety measure, an abnormality detecting circuit is added to vEA 250. l.Command Signal A low power DC voltage controls the outout current. An abnormality detecting circuit and a feedback circuit are added to VEA 250, Use of a sensor gives a wider control range and more precise control. veA252 2.
However, a oreat deal of force will be needed to manually op6ration this valve in order to over@methe mechanical spring as well as the air pressure assisting the spring.
Number of fingers and therefore, mg F 2 x With "a" as the safety margin, F is determined as follows: mg F = x a 2 x When = 0.2 When = 0.1 mg F = x 4 2 x 0.2 mg F = x 4 2 x 0.1 = 10 x mg = 20 x mg 10 x work piece weight 20 x work piece weight (Note) Even in cases where the coefficient of friction is greater than = 0.2, for safety reasons, P/A recommends selecting a gripping force which
The thread size is the same as standard.
Keep the product close to the nozzle as much as possible.
D A protocol that automatically allocates information, necessary to be registered to use the network, such as an IP address, to individual devices connected to the TCP/IP network. DHCP A Dummy slave can be used to reserve a dummy area within the I/O map.
This product operates as a slave. It does not send any requests.
Therefore, do not use it in an environment that is exposed to chemicals such as thinner, carbon tetrachloride, chloroform, acetic ester, aniline, cyclohexane, trichloroethylene, sulfuric acid, lactic acid, or water-soluble cutting oil (alkalinic). Do not use the product in direct sunlight.
This function prevents detection of such temporary drops in the supply pressure as an error. Response time settings: 20 ms, 160 ms, 640 ms, 1280 ms
Manual release bolt Design minimizes influences of unlocking air quality A design largely unaffected by factors such as moisture and condensate in compressed air has been realized by separating the lock mechanism and the brake cylinder. Can be locked in both directions An equal holding force can be obtained on either reciprocating stroke of the cylinder.
It is suitable for use in cases where water must be removed, but the air does not have to be as dry as when an air dryer is used or an air dryer cannot be used because an electric power supply is not available.
an n r tio ta n r Ro +8 0 io Ro tat tat Ro 80 io t 1 n r fla an ge gle of sin +10 0 Ro tat 90 ion t 1 ra fla ng le e o ing f s With external stopper For 90 For 180 Single flat Single flat A n 5 5 gl e ge ge ad an an ju t r t r st en m en en stm m t r st ju ju an ad ad ge le e Ang 5 gl n A B port A port B port A port 90 A 5 n gl ge e an ad t r ju en st m 180 Note) The drawings show
an n r tio ta n r Ro +8 0 io Ro tat tat Ro 80 io t 1 n r fla an ge gle of sin +10 0 Ro tat 90 ion t 1 ra fla ng le e o ing f s With external stopper For 90 For 180 Single flat Single flat A n 5 5 gl e ge ge ad an an ju t r t r st en m en en stm m t r st ju ju an ad ad ge le e Ang 5 gl n A B port A port B port A port 90 A 5 n gl ge e an ad t r ju en st m 180 Note) The drawings show
As a rough guide, tighten the screw an additional 90 after feeling a tight resistance. As a rule, it should be turned about 90 beyond the point at which tightening can be felt. 0.5 0.2 0.3 MHL2-20D 0.5 0.2 0.2 MHC MHL2-25D 0.2 0.1 0.2 MHL2-32D 0.4 0.4 0.7 MHT MHL2-40D 0.2 0.4 0.7 MHY MHW MRHQ Misc.