AIR GRIPPER Hexagon socket head cap screws. (2) Loosen hexagon socket head cap screws, Body B and then remove them from the Body A. Body A Guide bolt (3) Push the seal support so that the rod cover comes out of the Body B end surface. Rod cover Seal support Body B (4) Remove the lever shaft and lever. Lever shaft Lever (5) Pull out the rod cover and piston assembly and replace the seal.
(Equivalent lead (5)Storke [mm] (7)Cable type (6)Motor option Size Without cable Nil Nil Without option Standard cable 16 25 S R B With lock Robotic cable (Flexible cable) 50 100 150 (10)I/O cable length * (9)Driver type * [m] (8)Cable length * [m] Power supply Without cable Nil Nil Without cable Compatible driver voltage(V) Without cable (Connector only) H 2 2 Nil Without driver 1
B) N MODEL IL100 BLOCK DIAGRAM -4- 4.
The output number starts at the A side and then B side in that order as shown in figure a. If a single-solenoid valve is mounted on the standard wiring manifold, the output number for the B side solenoid valve is skipped. Custom wiring for the mixed mounting single-solenoid valves and the double-solenoid-valves can be specified with a Wiring Specification Sheet.
(Refer to fig. b) : Each bit of data sent from master (4 bytes) shows ON/OFF (0: OFF, 1: ON) of solenoid valve.
For safety operation of SMC Refrigerated Air Dryer, read thoroughly and follow stated safety instructions, as well as regulation stated within ISO 4414*1 & JIS B 8370*2. *1) ISO 4414: Pneumatic fluid power Recommendations for the application of equipment to transmission and control systems. *2) JIS B 8370: Pneumatic fluid power General rules relating to systems This manual explains about
The B time delay will be changed to position B (approximately 40 seconds) when the input signal pressure is increased to 0.8 MPa. Input signal pressure (MPa) Fig. 3: Relationship between the input signal pressure and time delay (3) Reset time The time delay from when Input is turned OFF until Output is turned OFF is the Reset time.
Dual power supplies B. Single power supply Figure 3 Figure 4 : Communication connector FG and FG terminal are connected inside the SI unit.
2 Safety Instructions Continued 1) Inspection and maintenance of machinery/equipment should only be 3 Specifications Continued 3 Specifications Continued HEC-OM-U015-B HECR012-W performed after confirmation of safe locked-out positions.
B) In the state of A), attach the workpiece and the arm side block, and adjust the shim so that there is a space of about 0 mm. During this step, theoretically, there is no clamping force pressing down on the workpiece. C) In order to generate a clamping force from the state described in step B), insert an additional shim.
Description Product number Remarks Sound Absorbing Material A Sound Absorbing Material B Suction filter 9 Silencer set ZL112-SP01 10 11 ZL212 Series No. Description Product number Remarks 10 Silencer set ZL212-SP01 Sound Absorbing Material A Sound Absorbing Material B 9 17 - Doc. no.
Size of width across flats is 4 which is standard by JIS B 4648. 7) Speed control When controlling the cylinder speed, install SMCs speed controller, Series AS, on the position near to the supply port for air and control the cylinder speed to the specified speed.
JIS B 8361: General rules for hydraulic equipment. JIS B 9960-1: Safety of machinery Electrical equipment for machines. (Part 1: General requirements) JIS B 8433-1993: Manipulating industrial robots Safety. etc. *2) Labor Safety and Sanitation Law, etc. Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury.
Doc. no.CA2*-OM0071P-B PRODUCT NAME Air cylinder MODEL / Series / Product Number / Contents Safety Instructions P2 1. Specifications P4 1-1. Specifications 2. Installation and Handling P4 2-1. Air supply 2-2. Design 2-3. Mounting and Installation 2-4. Environment 2-5. Speed control 2-6. Allowable kinetic energy 2-7. Air cushion 2-8.
coated 9 Bumper A Resin 1 10 Bumper B Resin 1 11 Retaining ring Stainless steel 1 12 Bushing for clevis Bearing alloy 1 13 Rod seal NBR 1 14 Piston seal NBR 1 15 Piston gasket NBR 1 16 Wear ring Resin 1 17 Nut Carbon steel 1 Nickel plated 18 Rod end nut Carbon steel 1 Zinc chromated 18 Series CQSY DC: Basic type DCM: Rod end male thread Construction of CQSY12 to 25 Parts list No.
Fig. 3-2 [Ex.-2] 5 B Load base Guide shaft Bearing A External slider Cylinder tube Detail of A Wrong example Correct example View A Load base Load base External slider Spacer Clearance External slider Detail of B Detail of B By tightening of the bolt, the load base and Insert the spacer to keep flexibility in cylinder body and load base even after the bolt is tightened. cylinder body are
JIS B 8361: General rules for hydraulic equipment. JIS B 9960-1: Safety of machinery Electrical equipment for machines. (Part 1: General requirements) JIS B 8433-1993: Manipulating industrial robots Safety. etc. *2) Labor Safety and Sanitation Law, etc. Caution Operator error could result in injury or equipment damage.
(ASME B40.1 Grade B or better) psig/bar 4) (No code) Accuracy Cleanliness No oil ASME B40.1 level IV No oil Brass Polycarbonate Brass Phosphor bronze B Case Window Socket Bourdon tube Material MPa MPA 1.14 (29) 2.28 (58) 2.1 (53.5) 2.12 (54) NPT 1/4 0.42 (10.5) inch (mm) 3) Part number of pressure gauge itself.
4 O-ring Body B NBR Stainless steel 303 r !5 O-ring Body B NBR Stainless steel 303 t !6 Needle O-ring NBR Stainless steel 303 y !7 O-ring Seat ring NBR Stainless steel 303 u !8 O-ring Needle guide NBR Stainless steel 303 i !9 Gasket Lock nut M5 type only NBR, Steel Stainless steel 303 o @0 Lock nut Spacer PBT Note) Stainless steel 303 !
If using other screws, switch may be damaged. 12-13-16 17 Solid State Switch Direct Mounting Style D-Y59 /D-Y69 /D-Y7P(V) A B A B For details about certified products conforming to international standards, visit us at www.smcworld.com.