MHR2/MDHR2, MHR3/MDHR3 Rotary Actuated Air Gripper (2 Finger) (3 Finger) As a rough guide, thighten the screw an additional 90o after feeling a tight resistance. Switch reset position(OFF) MHZ2 MHZJ2 Protrusion of Auto Switch from Edge of Body MHQ The maximum protrusion of an auto switch (when fingers are fully open) from the edge of the body is shown in the table below. Use the table as a guideline for mounting.
However, a oreat deal of force will be needed to manually op6ration this valve in order to over@methe mechanical spring as well as the air pressure assisting the spring.
A digital pressure gauge is recommended for such situation or as deemed necessary. Air Supply Warning 1. Use a mist separator on the inlet side of the product. If the supplied air contains condensate or dust, the bleed mechanism can malfunction. 2. Do not use a lubricator on the inlet side of the product, as the bleed mechanism can malfunction. Caution 1.
A digital pressure gauge is recommended for such situation or as deemed necessary. Air Supply Warning 1. Use a mist separator on the inlet side of the product. If the supplied air contains condensate or dust, the bleed mechanism can malfunction. 2. Do not use a lubricator on the inlet side of the product, as the bleed mechanism can malfunction. Caution 1.
Model vEA 250/130 Basic type having driving function only w 251 As a system satety measure, an abnormality detecting circuit is added to vEA 250. l.Command Signal A low power DC voltage controls the outout current. An abnormality detecting circuit and a feedback circuit are added to VEA 250, Use of a sensor gives a wider control range and more precise control. veA252 2.
Keylock function Prevents operation errors such as accidentally changing setting values. Setting of security code The user can select whether a security code must be entered to release key lock.
Anti-chattering function Pressure Momentary change Devices such as large bore cylinders and high-flow vacuum ejectors consume a large volume of air when they operate, and this may cause a momentary drop in the supply pressure. This function prevents such momentary drops from being detected as abnormal pressures by changing the response time setting.
This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switch-mode power supply and the product, or by using a series power supply instead of a switchmode power supply. 3 DC(-) 2 4 These safety instructions are intended to prevent hazardous situations and/or equipment damage.
Set OUT2 same way as OUT1. Maintenance Bracket A or D(Model: ZS-24-A/ZS-24-D) Bracket B (Model: ZS-24-B) [01/N01 type] [W1/WF1 type] Operator How to reset the product after power cut or forcible de-energizing The setting of the product will be retained as it was before a power cut or de-energizing.
This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switch-mode power supply and the product, or by using a series power supply instead of a switch-mode power supply. Default setting The default setting is as follows. If no problem is caused by this setting, keep these settings.
If this surface is to be used for mounting, a spacer composed of a non-magnetic substance (aluminum, etc.) is required as shown in the figure below.
This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switch-mode power supply and the product, or by using a series power supply instead of a switchmode power supply. Function selection mode Key-lock function To set this function, refer to SMC website (URL http://www.smcworld.com) for more detailed information or contact us.
location where it will be used as a support.
This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switchmode power supply and the product, or by using a series power supply instead of a switch-mode power supply.
With gasket is provided as standard. Type Applicable tubing O.D.
Mounting Never mount the product in a place that will be used as a mechanical support during piping. Never mount the product upside down. Attach the piping so that the fluid flows in the direction indicated by the arrow on the body. The monitor with integrated display can be rotated. Rotating the display with excessive force will damage the end stop.
This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switchmode power supply and the product, or by using a series power supply instead of a switch-mode power supply.
As an air slide table has magnets built-in, do not allow close contact with magnetic disks, magnetic cards or magnetic tapes. Data may be erased. 4. When mounting an air slide table, use screws with appropriate length and do not exceed the maximum tightening torque. Tightening with a torque above the limit could malfunction.
There is a risk of unexpected malfunction. Do not use solvents such as benzene, thinner etc. to clean each unit. They could damage the surface of the body and erase the markings on the body. Use a soft cloth to remove stains. For heavy stains, use a cloth soaked with diluted neutral detergent and fully squeezed, then wipe up the stains again with a dry cloth.