Bore Size: 1 1/2", Stroke, Inch: 30, Stroke, Hundredths of an Inch: 00, Option: Oil-free Exterior

Bore Size: 1 1/2", Stroke, Inch: 40, Stroke, Hundredths of an Inch: 00, Option: Oil-free Exterior

Bore Size: 2 1/2", Stroke, Inch: 25, Stroke, Hundredths of an Inch: 00, Option: Oil-free Exterior

Bore Size: 2 1/2", Stroke, Inch: 20, Stroke, Hundredths of an Inch: 00, Option: Magnetic Sheilding Plate

Bore Size: 1 1/4", Stroke, Inch: 60, Stroke, Hundredths of an Inch: 00, Option: Oil-free Exterior

Bore Size: 2 1/2", Stroke, Inch: 20, Stroke, Hundredths of an Inch: 00, Option: Oil-free Exterior

Bore Size: 1 1/2", Stroke, Inch: 15, Stroke, Hundredths of an Inch: 00, Option: Oil-free Exterior

Bore Size: 1 1/4", Stroke, Inch: 12, Stroke, Hundredths of an Inch: 00, Option: Magnetic Sheilding Plate

Bore Size: 1 1/4", Stroke, Inch: 30, Stroke, Hundredths of an Inch: 00, Option: Oil-free Exterior

For details on daily and periodic inspections of MY series mechanically jointed rodless cylinders, and the causes and corrective actions to be taken in the event of an error, refer to the operation manual. For example, if the seal belt falls off, air will leak, but you can refer to the operation manual to see how to put the seal belt back on and continue operation.

It is possible to change from the energy-saving nozzle or high flow rate nozzle types to the female threads for piping type (Rc1/8) by replacing the body assembly. Refer to the following for body assembly part numbers.
Note) Old IZN10 and new IZN10E series body assemblies are not interchangeable.

The amount of discharged oil is listed in the “Specifications” section in the CQ2L□ air-hydro booster catalog.
This is the amount of oil that can reach a high pressure. The value obtained by dividing this amount of discharged oil (cm3) by the piston pressure receiving area (cm3) of the hydraulic cylinder under consideration is a reference for the stroke (cm) that can be used for high

IDX-OM-W035

IDX-OM-W035-B / Series IDFB22E-11 IDFB22E-11 K,R,S,T,V IDFB22E-23 IDFB22E-23 K,R,T,V IDFB37E-23 IDFB37E-23 K,R,T,V IDFB55E-46 IDFB55E-46 L,R,T,V IDFB75E-46 IDFB75E-46 L,R,T,V URLhttps://www.smcworld.com/ English instruction manual can be downloaded from our URLhttps://www.smcworld.com/ SMC () * 1 ) JIS B8370 * 2 ) ISO4414 *1) ISO4414Pneumatic fluid power General rules and safety requirements

Although it can hold the cylinder at an intermediate position for longer than the type with a closed center (metal seal), with the perfect valve, it cannot be guaranteed that the position will not deviate.
Note) If there is air leakage from the cylinder or piping, even the perfect valve position will deviate quickly.

No, there is no seal kit for the MXZ series because the product cannot be disassembled. For further details, refer to the catalog.
The MXZ series catalog can be found here.

This is possible using the special order part number “MRHQ∗∗-∗SX-∗-∗-X103.” The rotation starting point can be changed by 90° based on the piping port surface. For details on the MRHQ-X103, refer here.

A signal to the BK-RLS terminal for brake release is only required when it needs to be released forcibly during adjustment or an emergency. It should remain OFF during normal operation.

For an actuator with a small lead, it is difficult to move a moving part such as a table with external force. In this case, insert a flathead screwdriver into the manual override screw on the motor part and turn it to operate it.

If the table is manually swung, the drive section may be damaged.
Swing the table with the manual override screws on both sides of the unit.

Refer to the following internal circuits and wiring examples. For NPN, a switch is mounted between gray (FUNC) and blue (minus), and when the switch is turned ON, a suction command signal is output and automatic control is performed.
Note) For PNP, a switch is mounted between gray (FUNC) and brown (plus).

Internal circuit and wiring example 1: NPN output type, NPN open collector