While the current operating mode is displayed, press the UP or DOWN button to select a newly desired operating mode. This function stores the measuring pressure that is set during the auto preset mode as a basic value. While the current setting is displayed, press the UP or DOWN button to select it as an auto preset setting.
Diaphragm Style Flow Switch Series IFW5 How to Order ZSE ISE The flow switch, series IFW is used for detection and confirmation of the flow as a relaying device for the general water applications in some various equipment such as cooling water fixture in the industrial machinery.
The minimum pressure can be set as low as 0% and as high as 50% of the full span. The maximum pressure can be set as low as 10% and as high as 100% of the full span. For example, an ITV203 could be set to output 35 PSI at 0% input signal, and 43 PSI at 100% input signal (there must be at least 8 PSI separation).
The size should be 6 or 4.5 and length should be a maximum of 20 m, but the collector,s performance will decline as the tube gets longer, so be sure to use as short a connecting tube as possible.
Therefore, the amount of condensed water is as following.
a push button guard: KEA AS-D Body (Red) Residual pressure release push button (Red) Example of air cylinder residual pressure release time D Release button (Blue) Release button (Blue) AS-T 0.6 Pressure in the cylinder MPa D L1 Q Condition: Cylinder I.D. 100 Stroke 200 mm ASP 0.5 B A D 0.4 8 4.2 ASN Applicable tubing W (mm) 0.3 M M L2 L2 Applicable tubing Weight (g) Model Applicable tubing
T h e V YH y R e g R a n g e i s c o n s t r u c t e d b y u t i l i z i n g a standard control unit either alone (VY1D00-M5) or as a Pilot Valve controlling one of the Range of VEX1 Power Valves.
Note 2) When used as a common external pilot, select the internal pilot specification as an applicable valve. Note 3) Gasket and mounting bolts are equipped.
Especially in the case of long strokes, implement measures such as providing a guide for the load.
0.56 0.66 0.70 B 0.56 0.66 0.70 A 1.50 1.81 2.29 A 1.50 1.81 2.29 B 0.48 0.58 0.61 B 0.48 0.58 0.61 A 1.42 1.72 2.21 A 1.42 1.72 2.21 B 0.60 0.70 0.74 B 0.60 0.70 0.74 A 1.54 1.85 2.33 A 1.54 1.85 2.33 B 0.37 0.46 0.50 B 0.37 0.46 0.50 A 1.30 1.61 2.10 A 1.30 1.61 2.10 Bore Bore 075 (3/4") 106 (1 1/16") 150 (1 1/2") 075 (3/4") 106 (1 1/16") 150 (1 1/2") Mounting Height (NCDM) (in) D-C7 D-C80
1 2 Holding block (A) 1 2 1 Switch block (A) 1 1 Switch block (B) 1 1 Holding block (A) 1 No.
exhaust center 2(B) (A)4 2(B) (A)4 (R1)5 1 (P) 3(R2) (R1)5 1 (P) 3(R2) How to Order Manifold Base 3 position pressure center 2(B) (A)4 Same manifolds as SYJ5000 series are prepared.
4 (A) 4 1 (P) 3 (R) 5 (R) 1 (P) 3 (R) How to Order Manifold Base 2 position double 2 position double (B) 2 (A) 4 (B) 2 (A) 4 Same manifolds as series SYJ3000 are prepared. 1 (P) 3 (R) 5 (R) 1 (P) 3 (R) SS5YJA3 Fill the same as SS5YJ3 3 position closed center 3 position closed center (B) 2 (A) 4 (B) 2 (A) 4 Instruct by specifying the valves and blanking plate assembly to be mounted on the
A (mm) Model A 110 120 171 B 38 48 66 C 1 1 2 D 30 40 55 Fn 34 70 Fc 17 26 41 G 40 39 63 H J P.C.D L1 6 x 4.4 6 x 6.6 L2 XMC-16 XMC-25 XMC-40 40 50 65 26 28 36 P.C.D 27 P.C.D 58.7 XMC-50 to 80/Angle type C L2 D Fd Fc L1 (KF flange) Fn C (K flange) (CF flange) H J K B G A A (mm) Model A 183 209 250 B 80 100 117 C 31 39 45.5 D 75 87 114 Fn 95 110 Fd 114 Fc 52 70 83 G 77 76.5 105 H J K
B 1 0 A B 1 0 A B 1 0 A B 1 0 9 61.5 A A A A R4.5 26 62.5 97 = 4.5 (5.5) (35) (L3) (5.2) 52 (L4) Stations D side U side 1 2 3 4 5 6 7 8 n 2-C6 P(SUP) port P A P A A A A A A A 24.5 (11) 13.5 R B R B B B B B B B (7.5) 7 2-C6 R(EXH) port 19.2 P = 11 2n-C3, C4, C6, M5 C3: One-touch fitting for 3.2 C4: One-touch fitting for 4 C6: One-touch fitting for 6 M5: M5 threads Broken lines indicate DIN
Use the tip of the watchmakers flat blade screw driver to insert the clip to the end properly. 1) Insert a watchmakers flat blade screw driver along with taper of hole B on OUT side of the body. 2) Hook the tip of the screw driver to the inserted clip, and pull out the clip. As the clip may fly out, pull it slowly as holding it with a hand. 3) Pull out the mounted One-touch fitting.
Use the tip of the watchmakers flat blade screw driver to insert the clip to the end properly. 1) Insert a watchmakers flat blade screw driver along with taper of hole B on OUT side of the body. 2) Hook the tip of the screw driver to the inserted clip, and pull out the clip. As the clip may fly out, pull it slowly as holding it with a hand. 3) Pull out the mounted One-touch fitting.
When this is the case, decrease the supply pressure as much as possible or slightly increase the set pressure and restrict the output line (such as by adding a throttle valve to adjust the pressure). Can also be used in an intensive piping system.
A short circuit breaker or fuse should be installed. 4. When a valve is to be heated, only the body section should be heated, excluding the bonnet (handle) section. 5. When a heater is in operation, the entire valve becomes hot. Be careful not to touch it with bare hands, as burns will result. Piping Caution Selection Caution All models 1.
Use this as a standard when mounting, etc. D-F8 has no protrusion from the body's end surface.