MHL2 After setting the position, tighten the attached switch mounting set screw with a flat head watchmakers screwdriver. Auto switch hysteresis is as follows. Please refer to the table as a guide when setting auto switch positions.
Air pressure may not rise with an air compressor of smaU capacity. 8 When source air is very dirty, use a main line filter (Series AFF) as a prefilter. When a reciprocating type compressor is used, use a main line filter(Series AFF) as a prefilter. Use an air compressor with the following capacity: AMH150 AMH650 100.Q.
How to reset the product after a power cut or forcible de-energizing The setting of the product will be retained as it was before a power cut or de-energizing. The output condition is also basically recovered to that before a power cut or deenergizing, but may change depending on the operating environment.
[A ir ] dry air, N2 [FLU] Operating fluid [F 3] Check that the above preparation has been performed correctly, then part A shown should be pressed in by hand to make temporary connection. Part A should then be pressed in using a suitable tool, such as pliers. The sensor connector cannot be re-used once it has been fully crimped.
Air flow direction: Port P Block, A R VT DIN terminal and terminal (with light/surge voltage suppressor) are connected inside as in the figure below. Connect to the corresponding power supply.
PC Connect the EX series to a PC via a switching hub.
How to reset the product after a power cut or forcible de-energizing The setting of the product will be retained as it was before a power cut or de-energizing. The output condition is also basically recovered to that before a power cut or deenergizing, but may change depending on the operating environment.
l102Gl .lnsulalion resistanceMin. 50O (between lead wi and 6) as memured with a sooVDC meger .
This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switch-mode power supply and the product, or by using a series power supply instead of a switch-mode power supply. Error indication Do not use the product in a place where static electricity is a problem. Otherwise it can cause failure or malfunction of the system.
Keep the product close to the nozzle as much as possible.
Use a tishrenirE toqu of 0.05-0.rN.m(05-1.o2kgl.cm)-As a rcuqh guide, tishten the screw thrcush a flrih. 9d after teelins a tisht screv, (M2.5 x 4x ) Compact Guide Cylinder : Series MGQ XBII long stroke 32, 40. 50, 63, 80, 100 Same specifrcations as page 1. 125 ,150 ,17 5,20A MGQM . MGQL Common Dimensions
This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switchmode power supply and the product, or by using a series power supply instead of a switch-mode power supply. [2nH] Input of the Set value for the upper 3 digits (OUT2) [ 0] Hysteresis mode 2 Bracket Bracket for mounting the product.
Even if a proper plier (tool for installing a C retaining ring) is used, it is likely to inflict damage to a human body or peripheral equipment, as a retaining ring may be flown out of the tip of a plier (tool for installing a C retaining ring). Be much careful with the popping of a retaining ring.
The AS speed controller variants with push lock allow for easy locking of the flow rate setting without a tool. Elbow type, speed control with one-touch fitting ; Improved, larger push-lock handle ; Easy identification of meter-in (blue handle) vs. meter-out (gray handle) ; Max. operating pressure 1MPa ; Applicable tubing material: nylon, soft nylon, polyurethane
Using SMC flow controls with built in one-touch fittings minimizes installation time, reduces mounting height and enables a more compact machine design. These flow controls allow the body to be rotated to facilitate simple installation.
(Parts cannot be replaced for the old VH series valve with a silver body.)
The AS speed controller variants with push lock allow for easy locking of the flow rate setting without a tool. Elbow type, speed control with one-touch fitting ; Improved, larger push-lock handle ; Easy identification of meter-in (blue handle) vs. meter-out (gray handle) ; Max. operating pressure 1MPa ; Applicable tubing material: nylon, soft nylon, polyurethane
As a result, it is necessary for the customer to verify compliance with the EMC directive for the machinery and equipment as a whole. * Select Nil for anything other than JXCD1. RA Robotic cable 10 m*1 RB Robotic cable 15 m*1 When selecting an electric actuator, refer to the model selection chart of each actuator.
Press Part A by hand for temporary fixing. Press in the central part of Part A vertically with a tool such as pliers. A sensor connector cannot be taken apart for reuse once it is crimped. If the wire arrangement is incorrect or if the wire insertion fails, use a new sensor connector.