F/ISE This produces an air cushion cylinder which retains the merits of a compact design. Operating principle q When the piston is retracting, exhaust is discharged from both A and A' until piston seal H passes the air passage A. A + A' A' w After piston seal H has passed the air passage A, exhaust is discharged only from A'.
If there is a risk of contact, provide safety measures such as a cover or a system that uses sensors that will activate an emergency stop before contact is made. 2. Use a balance circuit in which lurching of the piston is taken into consideration.
Basic (Through-hole/Both ends tapped common): CQUB F Q 2 x M5 x 0.8 Y 4 x M6 x 1 depth 10 4 x 5.4 through 15 KA H H1 Rod end nut Width across flats B1 NY EY D X C1 K NX A + Stroke B + Stroke L EX L1 Rod end male thread Basic (mm) Size Stroke range (mm) A B D EX EY F H K KA L NX NY Q Y 20 25 32 40 5 to 50 49 42.5 10 22 47 11.5 M5 x 0.8 depth 8 5 8 6.5 5.5 36 15 3 5 to 50 49 42.5 10 24 53 11
to 63 32 to 63 A B U B A U D-P3DWA 32 to 63 U B A Auto Switch Proper Mounting Position D-F7/J79 D-F7V D-J79C/F7W D-F7WV D-F7BA D-F7BAV D-F79F/J79W D-A7H/A80H D-A73C/A80C D-A72 D-M9 D-M9V D-M9W D-M9WV D-M9A D-M9AV D-A9 D-A9V D-A79W D-A73 D-A80 D-F7NT D-P3DWA Bore size (mm) A 25.0 24.0 26.0 19.5 23.5 24.0 A 28.0 27.0 29.0 22.5 26.5 27.0 A 30.5 29.5 31.5 25.0 29.0 29.5 B 10.0 12.0 13.0 13.0
A Model Mounting Auto switch operating range A B A B A B 54 MXY6 34 MXH 59 5 MXY8 39 MXU 67 MXY12 47 MXS Solid State Auto Switch D-M9B(V), D-M9N(V), D-M9P(V) Lead wire entries inside MXQ (mm) B B Model Mounting Auto switch operating range MXF A B A B A B 50 MXY6 3 38 MXW 55 MXY8 3.5 43 MXJ 63 MXY12 3 51 MXP Lead wire entries parallel 2-Color Display Solid State Auto Switch D-M9BW(V), D-M9NW
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
Even if a proper tool is used, it is likely to inflict damage to a human body or peripheral equipment, as a snap ring may be flown out of the tip of a plier. Be much careful with the popping of a snap ring. Besides, be certain that a snap ring is placed firmly into the groove of rod cover before supplying air at the time of installment.
(A set of above nos. q to !5.)
Construction Diaphragm Seat Body 1110 B Diaphragm Valve for Ultra High Purity Air operated type Series AZ3542 & 4542 Dimensions inch (mm) AZ3542 & 4542 Ports: 2PW (Welded) Ports: 2P (Machined) M5 x 0.8 Actuation port Actuation port M5 x 0.8 1.57 (40) 1.57 (40) FORGED BODY BAR STOCK BODY Note) 2.24 (57) 2.24 (57) 0.44 (11.2) 0.44 (11.2) A A B A A Connections: MV, FV Connections: MV B A A A
Caution: Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
Mounting screw(M3) Tightening torgue 0.5 to 0.7Nm A DIN rail mount bracket fig. 3 When setting to DIN rail, place A of fig. 3 into DIN rail. While pushing it, fix it by the clamp of screw in fig. 4. Inadequate pushing may cause falling of parts.
Model AU ALU ALHU F R Barb fitting M3, M5 M3 M5 Barb elbow Barb one-touch Reducer Removing tubing Withdraw the sleeve straight along the tubing. Use a tool such as long-nose pliers if it is difficult to pull out by hand. 1. Withdraw the tubing straight. 2.
Model AU ALU ALHU F R Barb fitting M3, M5 M3 M5 Barb elbow Barb one-touch Reducer Removing tubing Withdraw the sleeve straight along the tubing. Use a tool such as long-nose pliers if it is difficult to pull out by hand. 1. Withdraw the tubing straight. 2.
A trunnion cannot be attached to a cover with a lock installed. Lock Specifications 2. Locking type manual override While pressing the M/O knob, turn it 90 counter clockwise. When the mark on the cap is aligned with the OFF mark on the M/O knob, the lock will be released (the lock will remain in a released condition).
8m to 20m)] Signal name Terminal (a) (b) LE CP B Cable colour Terminal number number Brown 2 A B-1 Red 1 A A-1 Cable length [L] Orange 6 B B-2 Yellow 5 B A-2 8 8mNote) Green 3 COM-A/COM B-3 Blue 4 COM-B/ A-3 A 10mNote) (c) Shield B 15mNote) Cable colour Terminal number Brown 12 Vcc B-4 C 20mNote) Black 13 GND A-4 Red 7 A B-5 Note) Produced upon receipt Black 6 A A-5 Orange 9 B B-6 of order
name Terminal Cable colour Terminal number number Brown 2 A B-1 Red 1 A A-1 Cable length [L] Orange 6 B B-2 Yellow 5 B A-2 8 8mNote) Green 3 COM-A/COM B-3 Blue 4 A 10mNote) COM-B/ A-3 (c) Shield B 15mNote) Cable colour Terminal number Brown 12 Vcc B-4 C 20mNote) Black 13 GND A-4 Red 7 A B-5 Note) Produced upon receipt Black 6 A A-5 Orange 9 B B-6 of order Black 8 B A-6 (Only "Robotic type
Terminal LE CP B Cable colour Terminal number number Brown 2 A B-1 Red 1 A A-1 Cable length [L] Orange 6 B B-2 Yellow 5 B A-2 8 8mNote) Green 3 COM-A/COM B-3 Blue 4 COM-B/ A-3 A 10mNote) (c) Shield B 15mNote) Cable colour Terminal number Brown 12 Vcc B-4 C 20mNote) Black 13 GND A-4 Red 7 A B-5 Note) Produced upon receipt Black 6 A A-5 Orange 9 B B-6 of order Black 8 B A-6 (Only "Robotic
Vertical Vertical m a a = 3000 a = 2000 200 L1 Mep 0 2 4 6 8 10 Transfer load m (kg) 600 a = 1000 a = 2000 L3 (mm) 400 a = 3000 a 200 L3 Mey 0 2 4 6 8 10 Transfer load m (kg) Refer to page 145 for deflection data. 26 Standard Motor/Vertical Mount Specification Series LJ1H10 Dimensions/LJ1H102PB Scale: 15% 10 6 Work piece mounting reference plane 80 5H10 depth 8 8-M5 x 0.8 thread depth 8