Card Motor Controller Controller Setting Software for LATCA （ For Window ®10 ） End-User License Agreement SMC Corporation (hereinafter referred to as "SMC") grants the user (regardless the user is a corporation or an individual) a license to use this software "Controller Setting Software LATC-Configurator" (hereinafter referred to as "Software") provided according to this End-User License agreement (hereinafter referred to as "Agreement") under the articles listed below
Use the table below as a guide when adjusting auto switch positions, etc.
Air filter (5 m or less) When using a solenoid valve, use a metal seal type (Series VQ, VQZ, SQ, etc.).
Mounting : Bolts lor lhrough hole model BSOB are as shown in table. How lo order : Stale"Bolf lollowedbydimensionsand quantily as shown.
Note) Contact P/A when replacing seals.
20C (68F) bend the tubing into a U shape.
If both plug and socket sides have connectors for SPEEDCON, the cable can be inserted and connected by rotating it 180, leading to a reduction in labor hours. A non-compatible connector can be connected to a compatible connector as well as an M12. 1. Be sure to turn the power off when connecting and disconnecting the connectors. 2. Do not touch the engagement surface with wet hands. 3.
) a = 3000 2000 m L1 0 10 20 30 Transfer load m (kg) L2 600 400 L2 (mm) Mer Rolling Yawing m 200 L2 Mer 10 20 30 0 Transfer load m (kg) m a = 1000 4000 a = 2000 L3 (mm) L3 a = 3000 2000 m Mey a 10 20 30 0 Transfer load m (kg) Refer to page 183 for deflection data. 164
Use it when you want to remove water but air as dry as that from an air dryer is not necessary, or when a power supply for an air dryer is not available, etc.
Use it when you want to remove water but air as dry as that from an air dryer is not necessary, or when a power supply for an air dryer is not available, etc.
End-User License Agreement SMC Corporation (hereinafter referred to as "SMC") grants the user (regardless the user is a corporation or an individual) a license to use this software "Controller Setting Software LATC-Configurator" (hereinafter referred to as "Software") provided according to this End-User License agreement (hereinafter referred to as "Agreement") under the articles listed below
When using a model with a heater, a mechanism to prevent overheating should be installed. Selection All models 1. When controlling valve responsiveness, take note of the size and length of piping, as well as the flow rate characteristics of the actuating solenoid valve. 2. Actuating press should be kept within the specified range.0.3 MPa to 0.5 MPa is recommended. 3.
Connection of piping to products When connecting piping to a product, avoid mistakes regarding the supply port, etc. Grommet Class B coil: AWG20 Insulator O.D. 2.5 mm Wiring Caution 1. As a rule, use electrical wire with a cross sectional area of 0.5 to 1.25 mm2 for wiring. Furthermore, do not allow excessive force to be applied to the lines. 2.
use a watchmakers screwdriver with a handle diameter of about 5 to 6 mm.
Thus, a used tube should be replaced with a new one or put in a different grip position after the operating cycles of 1 million times are reached as the guideline. 8. Avoid installing the coil vertically with its top to a downward direction. Should the tube break, the fluid could enter into the coil, causing the coil to burn out. 4.
The Real Time Clock can be used as a power saving device to automatically turn the equipment On/Off at scheduled times.
Labels are attached to indicate A and B side functions, using the same color as the manual override. Power (Current: consumption: 0.6 W 25 mA, 24 VDC) A side manual override: Orange A side passage symbol: Orange Pull the valve up at the front.
If using in an environment where it may be exposed to water splash, please take measures such as using a cover. 2. Provide adequate protection when operating in locations such as the following. Failure to do so may cause a malfunction or equipment failure.
REC Warning qDo not apply a lateral load to the cylinder piston rod. If a lateral load is applied to the cylinder piston rod, the rod could bend. Therefore, if the stroke is relatively long, take appropriate measures such as equipping the load with a guide. Similar precautions must be taken to prevent buckling.
This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switch-mode power supply and the product, or by using a series power supply instead of a switch-mode power supply. Do not use the product in a place where static electricity is a problem. Otherwise it can cause failure or malfunction of the system.