Large Size 3 Port Solenoid Valve VP3145/3165/3185 Series Rubber Seal in the figure below, this pilot-operated solenoid valve consists of a compact 3 port solenoid valve as the pilot valve and a large 3 port valve as the main valve.
L32 pin clamp cylinder available O Compact design makes it applicable to a broad range of workpieces. OContributes to a lightweight jig.
CAT.ES13-7 A Exhaust Cleaner for Clean Rooms Series AMP An exhaust cleaner that can be used inside a clean room. Series AMP Exhaust Cleaner for Clean Rooms An exhaust cleaner that can be used inside a clean room Exhaust air cleanliness: Equivalent to Class 100 (Consult SMC in advance, as this will differ depending on the operating conditions.)
Screw in piping while holding the upper body area (die-cast aluminum) with a wrench or other tool. Maintenance Caution 4. In cases such as common piping, reverse flow may occur depending on the timing for switching of solenoid valves, etc. In this situation, install a check valve on the upstream side. 1.
Plugging one of the cylinder ports (A or B) enables use as a 3 port valve. lt should not be used in special applications such as use as a non-leakage valve. Make sure the exhaust port is open if used as a 3 port valve. Solenoid {X) represents plugged port. common Exhaust ifflg"o,BJ"". rnd Pilot valve I Exhaust air from pilot valve will flow to main valve exhaust port.
As shown in the below figure, mount a crimped terminal (9), and then again tighten the screw (3e). Note) Tighten within the tightening torque of 0.5 Nm 15%. Note: a It is possible to wire even in the state of bare wire.
Plugging one of the cylinder ports (A or B) enables use as a 3 port valve. lt should not be used in special applications such as use as a non-leakage valve. Make sure the exhaust port is open if used as a 3 port valve. Solenoid {X) represents plugged port. common Exhaust ifflg"o,BJ"". rnd Pilot valve I Exhaust air from pilot valve will flow to main valve exhaust port.
If the pump is in a high position, idling sometimes occurs during re-start. Take measures such as releasing the air in a high position, etc. [Low temperature operation] The hydraulic fluid used becomes high viscosity when the temperature is low during the winter, etc., and the differential pressure indicator or the switch may activate.
Upper 3 digits Lower 3 digits Reverse output Warning: + ON Time Part A should then be pressed in using a suitable tool, such as pliers. 2 sec. OFF Initialize mode DANGER indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switchmode power supply and the product, or by using a series power supply instead of a switch-mode power supply.
This can be prevented by inserting a noise filter, such as a line noise filter and ferrite core, between the switch-mode power supply and the product, or by using a series power supply instead of a switch-mode power supply.
As soon as the work piece is moved within the detection range of the AirCatch Sensor the back pressure P2 increases. If P2 is equal or greater than P1, the switch output is ON. As soon as the work piece is outside of the detection zone the switch output is OFF. Gap too small Green 2 a Place the gap gauge on the detection nozzle for precise adjustment. s Confirm applied air pressure.
To install the fittings, screw the fitting into the hexagonal face of the body, applying the appropriate wrench as close to the thread as possible. Use a spanner corresponding to the size of hexagonal portion, or hexagonal portion may become deformed. 3.
Speed Controller with One-touch Fitting Elbow Type (Metal Body) AS Series AS-F AS-F Model TMH Speed controller with Applicable tubing O.D. Model Port size 4 6 8 10 12 ASD One-touch fittings for AS121-M5 AS221-01 AS221-02 AS321-02 AS321-03 AS421-04 M5 x 0.8 AS 1 8 R metal body specifications 1 4 R AS-FE 1 4 Uses flame resistant resin as standard.
As a guide, refer to the proper tightening torques shown below.
(If a gasket is installed in two places as in the case of a universal elbow or universal-tee type,tighten them two more times,namely by a half turn.) 60 50 -20 -10 0 Air temperature(C) Factor 10 30 40 0.94 0.95 1.08 1.06 1.04 1.02 0.98 0.97 15 Series VQ100 Opertion Guide Indicator Light and Surge Voltage Suppressor Latching Solenoid The latching solenoid is equipped with a self-holding mechanism
(or within 3 kPa ) 1/8 ARP ARP 1/4 For 0.2 MPa setting With backflow function (ARP20K/30K/40K) 3/8 IR-A 1/2 Installable between a solenoid valve and a cylinder : Standard : Semi-standard IR Direct operated precision regulator now available as a series!! (ARP20/30/40) IRV VEX SRH Applications Applications SRP a Apply a constant pressure to fluid. b Adjust the blow-line pressure.
As a result, it is necessary for the customer to verify final EMC conformity for the machinery and equipment as a whole. Caution Maximum speeds of actuators vary depending on the type.
As a result, it is necessary for the customer to verify final EMC conformity for the machinery and equipment as a whole. Caution Maximum speeds of actuators vary depending on the type.
(or within 3 kPa ) 1/8 ARP ARP 1/4 For 0.2 MPa setting With backflow function (ARP20K/30K/40K) 3/8 IR 1/2 Installable between a solenoid valve and a cylinder : Standard : Semi-standard IRV Direct operated precision regulator now available as a series!! (ARP20/30/40) VEX SRH SRP Applications Applications SRF a Apply a constant pressure to fluid. b Adjust the blow-line pressure.