VDW30/40-XF Do not apply external force to the coil when holding it to connect piping, as the tube may deform. When attaching fittings to a solenoid valve, do not use fittings that do not conform to the quick fastener standard. Handle with care when attaching fittings because the application of excessive stress to the quick fastener portion could damage the body. 1.
Do not repair or patch the replaced tubing or fittings for reuse. 1. Do not use in environments or locations where there is a danger of damage to fittings and tubing. For fitting and tubing materials, refer to specifications and construction drawings, etc. 2. Provide shade in locations which receive direct sunlight. Caution 1.
Design AT Caution Maintenance Caution IDl q Do not use this product in a line in which the pressure pulsation cycle is frequent. If it must be used under such conditions due to unavoidable circumstances, contact SMC beforehand. w Do not use it with anything other than dry air (such as air containing moisture).
Do not drop or bump. Do not drop, bump or apply excessive impact (1,000 m/s2) when handling. Even if the switch body is not damaged, the switch may suffer internal damage that will lead to malfunction. 2. Hold the product from the body side when handling. The tensile strength of the power cord is 49 N, and pulling it with a greater force can cause failure. 3.
5 32 3 16 1 4 5 16 3 8 1 2 1 2 17.46 17.46 17.46 22.23 25.4 28.6 -18 -20 9 16 -18 9 16 3 4 7 8 1-12 -14 -16 Bulkhead Male Elbow: KQ2LE Applicable tubing Applicable tubing O.D.
12 16 5, 10, 15, 20 25, 30 2.2-10 20 25 5, 10, 15, 20 25, 30, 35, 40 45, 50 Series CQS 12, 16 20, 25 12 16 20 25 5, 10 2.2-16 Solid state switch D-F9N, F9NV D-F9P, F9PV D-F9B, F9BV D-F9NW, F9NWV D-F9PW, F9PWV D-F9BW, F9BWV Series CQSK 12 16 5, 10, 15, 20 25, 30 20 25 5, 10, 15, 20 25, 30, 35, 40 45, 50 2.2-24 Series CQSlS 12 16 5, 10, 15, 20 25, 30 20 25 5, 10, 15, 20 25, 30, 35, 40 45,
) Note 4) (n = 4, 8, 12, 16) Note 4) (n = 4, 8, 12, 16) Note 4) (n = 4, 8, 12, 16) Note 4) 2 (Different surfaces and same surface), 1 60 75 65 85 15 D-M9V D-M9WV Note 1) (n 2) 2 (n 4) 2 (n 4) 2 (n 4) 2 (n 4) 2 60 + 30 15 + 30 75 + 30 65 + 30 85 + 30 n (n = 2, 4, 6, 8) Note 3) (n = 4, 8, 12, 16) Note 4) (n = 4, 8, 12, 16) Note 4) (n = 4, 8, 12, 16) Note 4) (n = 4, 8, 12, 16) Note 4)
KQ2P-23 KQ2P-04 KQ2P-06 KQ2P-08 KQ2P-01 KQ2P-03 KQ2P-07 KQ2P-09 3.2 4 6 8 16 16 18 20.5 31.5 32 35 39 1/8" 5/32" 1/4" 5/16" 16 16 18 20.5 31.5 32 35 39 3.2 6 8 10 5 6 8.5 10 Port plug VVQ0-58A The plug is used to block the cylinder port.
KQ2P-23 KQ2P-04 KQ2P-06 KQ2P-08 KQ2P-01 KQ2P-03 KQ2P-07 KQ2P-09 3.2 4 6 8 16 16 18 20.5 31.5 32 35 39 1/8" 5/32" 1/4" 5/16" 16 16 18 20.5 31.5 32 35 39 3.2 6 8 10 5 6 8.5 10 Port plug VVQ0-58A The plug is used to block the cylinder port.
21.5 28 34 41 6 6 6 8 16 21 25 30 6.3 12 10.3 18 7 10 11.5 14 3/16 3/16 +0.002 0 +0.002 0 +0.002 0 +0.002 0 +0.002 0 +0.002 0 #8-32UNC 3/16 3/16 #10-32UNF 5/16 5/16 1/4-28UNF 3/8 3/8 Knuckle pin and snap ring are contained.
2) Specified layout (up to 16 solenoids possible.) 16 16 stations Including the number of blanking plate assemblies.
Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not service machinery/equipment or attempt to remove components until safety is confirmed. 1. Inspection and maintenance of machinery/equipment should only be performed after confirmation of safe locked-out control positions. 2. When equipment is to be removed, confirm the safety process as mentioned above.
Do not service machinery/equipment or attempt to remove components until safety is confirmed. 1. Inspection and maintenance of machinery/equipment should only be performed after confirmation of safe locked-out control positions. 2. When equipment is to be removed, confirm the safety process as mentioned above.
Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
For details, refer to page 6-16-1.
16 16 8.5 8.5 8.5 M8 x 1.25 14.5 M8 x 1.25 14.5 M8 x 1.25 14.5 M5 x 0.8/ Effective thread depth 5 M5 x 0.8/ Effective thread depth 5 M5 x 0.8/ Effective thread depth 5 9.5 9.5 5 9.5 23 52.6 5 5 M10 x 1 M10 x 1 M10 x 1 Seal washer Width across flats 6 Seal washer Width across flats 6 26.5 56.1 Seal washer Width across flats 6 21 50.6 40 31 31 34.5 7 38 10 32.5 5 54 50 37 16 6 44 40 29.4 6
, 16 3/8, 16 1/2, 16 1500 2000 2500 3000 28.5 Composed effective area So (mm2) Composed effective area So (mm2) Composed effective area So (mm2) 100 RHC = 0.7 38 47 0.5 56.5 MK(2) 0.1 0.3 10, 12, 16 1/4, 3/8 50 RS Q G 500 15 63 RS H A 3/8, 16 1/2, 16 1/2, 16 3/4, 16 3/4, 16 1000 1500 2000 2500 3000 30 0 45 1,000 2,000 3,000 60 RZQ Maximum speed Vmax (mm/s) 75 89.5 80 MI W S 16 3/8, 1/2 500