Ｍ agnet Gripper Unit for Collaborative Robots Take measures to ensure air quality, such as by installing an aftercooler, air dryer, or water separator. Compressed air that contains a large amount of drainage can cause the malfunction of pneumatic equipment, such as air grippers. Therefore, take appropriate measures to ensure air quality, such as by providing an aftercooler, air dryer, or water separator. 4.
MHL2-10D MHL2-16D MHL2-16D MHL2-10D 2 1 2 1 60 60 25 25 0.6MPa 0.6MPa Holding force (N) Holding force (N) Holding force (N) Holding force (N) 50 50 20 20 0.5MPa 0.6MPa 0.5MPa 0.6MPa 40 40 15 15 0.4MPa 0.5MPa 0.4MPa 0.5MPa 0.4MPa 0.4MPa 30 30 10 10 0.3MPa 20 20 0.3MPa 0.3MPa 0.3MPa 0.2MPa 5 5 10 10 0.2MPa 0.2MPa 0.2MPa 10 20 30 40 50 60 70 20 40 60 80 100 120 20 40 60 80 100 120 0 0 0 10 20
25 30 0 5 10 15 20 25 30 Time of water flow (min) Measuring time (min) Test method and conditions The liquid contact portions were filled with sulphuric acid and left untouched for half an hour.
Valve specifications Note 1) Conductance is molecular flow measured with an elbow pipe which has the same dimension as each applicable flange. Note 2) For one cycle of cylinder.
Please contact SMC for use in an environment where the product is exposed to such liquid as cutting oil, lubricant oil or coolant oil. 15-7-12
Stroke ST (mm) 0 4 6 8 10 15 20 Caution Stroke ST (mm) When driving an inertial load, operate a cylinder with kinetic energy within the allowable value.
This is usually achieved by having dual channels of operation, such as dual valves, dual wiring, dual guard switches etc.
An environment where food which will be sold as merchandize, directly touches the fitting components. Installable Splash zone An environment where food which will not be sold as merchandize, directly touches the fitting components. An environment where there is no contact with food.
INLET (Upstream) is defined as a port connected to the region below the valve seat. It is illustrated with an arrow pointing towards the valve body or an "empty" triangle on the schematic. OUTLET (Downstream) is defined as a port connected to the region above the seat and below the diaphragm.
When used to supply water to boilers, substances such as calcium and magnesium which generate hard scale and sludge are included. Since this scale and sludge can cause valve malfunction, install water softening equipment, and a filter (strainer) directly upstream from the valve to remove these substances. Warning 1. Cannot be used as an emergency shutoff valve, etc.
Single Axis Electric Actuator Series LJ1S Series LJ1S Slider Guide Lead screw lead mm Mounting Page Model Series Guide type Motor type orientation Slide screw 20 20 20 20 20 20 LJ1S10 LJ1S20 LJ1S30 LJ1S10 LJ1S20 LJ1S30 88 Standard 90 motor 92 Slider guide LJ1S Horizontal 94 Standard 96 motor 98 Option specifications Page 100 Made to Order 101 Dust seal specification 116 TSUBAKI CABLEVEYOR
Use a contact protection box in cases such as with an induction load, when the lead wire is longer than 5m or with 100VAC. 1 Operating load is an induction load. 2 Wiring to the load is 5m or longer. Contact protection box internal circuits 3 Load voltage is 100VAC. CD-P11 Use a contact protection box in any of the above listed situations.
D A protocol that automatically allocates information, necessary to be registered to use the network, such as an IP address, to individual devices connected to the TCP/IP network. DHCP A Dummy slave can be used to reserve a dummy area within the I/O map.
D A protocol that automatically allocates information, necessary to be registered to use the network, such as an IP address, to individual devices connected to the TCP/IP network. DHCP A Dummy slave can be used to reserve a dummy area within the I/O map.
element needs cleaning (differential pressure cannot be returned as dust adheres) or an element or a seal needs replacement, clean or replace the element by following the dismantling procedure below. 2-1.
element needs cleaning (differential pressure cannot be returned as dust adheres) or an element or a seal needs replacement, clean or replace the element by following the dismantling procedure below. 2-1.
Stroke 25 36.5 5 22.5 10 14 20 10 20 10 (All dimensions but A and CL are identical to those of the basic style.)
C 2 m 16-3-20 20 Series PSE Specific Product Precautions 3 Be sure to read before handling. Wiring Caution 3. Connecting to other series Any pressure sensor (SW) can be connected as long as it generates analog output (1 to 5 V) signal. However, the pressure range must match. SMC pressure sensors, Series PSE510 & PSE520, are also connectable.
An injury or failure can result. Load Brown LINE(+) Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. 20 mm or more Sheath Main circuit + 12 to 24 VDC Do not operate in an atmosphere containing flammable or explosive gases.
D A protocol that automatically allocates information, necessary to be registered to use the network, such as an IP address, to individual devices connected to the TCP/IP network. DHCP A Dummy Remote can be used to reserve a dummy area within the I/O map.