Lubrication Equipment A 1 2 150 165 42.7 76.3 45 65 40 60 35 40 80 80 ALBA90-10 ALBA90-20 1.17-24
In particular, avoid application of pressure above the specifications caused by a water hammer.
A model should be selected with a holding force of 10 to 20 times that of the component weight. If high accelleration, decelleration or impact forces are encountered during motion a further margin of safety should be considered.
System configuration Make sure to install a mist separator (Series AM) on the inlet side of the booster valve. Also install a cleaning device such as an air filter or a mist separator on the outlet side as necessary. Because the booster valve contains a sliding mechanism and the inner wall of the tank for the booster valve is untreated, dust flows out to the secondary side.
When a surge generating a load such as a relay or solenoid is directly driven, use a type of switch with a built-in surge absorbing element. 4. Since the type of fluid varies depending on the product, be sure to verify the specifications. The switches do not have an explosion proof rating. To prevent a possible fire hazard, do not use with flammable gases or fluids. 5.
or more for Air pressure lock-up Sol A, B & C accept direct-operated type or pilot operated type. As you find that Solenoid valve Sol A for lock releasing is independent, you can use a compact 3-way valve and mount it dkeclly io lock-po[i by means of a nipple so that you can get the time delay of locking as short as possible. Diagram 6.
or more for Air pressure lock-up Sol A, B & C accept direct-operated type or pilot operated type. As you find that Solenoid valve Sol A for lock releasing is independent, you can use a compact 3-way valve and mount it dkeclly io lock-po[i by means of a nipple so that you can get the time delay of locking as short as possible. Diagram 6.
Cylinder with Lock Series MNB Taper ring Steel ball P f R R High locking efficiency Improved locking efficiency, as well as stable locking and unlocking (unlocking pressure 0.25MPa. 0.05MPa compared to conventional P/A products) have been realized by arranging a large number of precision steel ball bearings in two circular rows.
When not using this product as a replacement for HRG/HRGC, this function is not needed.
Install a mist separator (Series AFM) as a preliminary filter on the inlet side of the micromist separator to prevent premature clogging. 2. Do not install on the inlet side of the dryer as this can cause premature clogging of the element. Drain M5 x 0.8 AFD30, 40 Maintenance Float type auto drain OUT IN N.C. N.O. Warning 1.
at a constant or low speed or to effect an intermediate stop, just like a hydraulic unit, while using pneumatic equipment such as a valve.
Standard Strokes Bore size [mm] Standard stroke [mm] 12, 16 5, 10, 15, 20, 25, 30 20, 25, 32, 40 5, 10, 15, 20, 25, 30, 35, 40, 45, 50 50, 63, 80, 100 10, 15, 20, 25, 30, 35, 40, 45, 50 Intermediate strokes are available as a special order.
) 1 Note 1) 0 Note 1) For construction No.1(with terminal box), the ambient and fluid temperatures are as follows: Exd2BT5 20 to 60C Non-explosion proof (non hazardous Iocations only) 20 to 80C The positioner body is EXd2BT5 labeled.
Applicable bore A 0.51 D C 1/4-28 UNF B 0.16 JM-025 0.44 3/4", 7/8" JM-03 0.50 0.19 5/16-24 UNF 0.50 1 1/16" JM-045 0.69 0.79 0.26 7/16-20 UNF 1 1/4", 1 1/2" JM-04 0.56 3/8-24 UNF 0.65 0.23 1 1/4", 1 1/2" (Non-rotating) JM-05 0.75 1/2-20 UNF 0.32 0.87 2" 6-14-20 21 Series NCM Mounting Bracket Accessory Material: Rolled steel P dia.
Take appropriate measures against noise, such as using a noise filter, when the product is incorporated into equipment.
F A A Lr MXF8 Lr = 20 mm 0.04 0.04 0.08 MXF8-30 Table displacement amount (mm) Table displacement amount (mm) Table displacement amount (mm) MXF8-30 0.03 0.06 0.03 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com MXF8-20 MXF8-10 MXF8-20 MXF8-30 0.02 0.04 0.02 MXF8-
Use it when you want to remove water but air as dry as that from an air dryer is not necessary, or when a power supply for an air dryer is not available, etc.
Use it when you want to remove water but air as dry as that from an air dryer is not necessary, or when a power supply for an air dryer is not available, etc.
Fine Lock Cylinder with Guide Series MLGC 20, 25, 32, 40 A linear transfer cylinder unit with a built-in locking mechanism and a guide rod integrated in a compact design.
Fluid quality The use of fluid which contains foreign matter can cause problems such as malfunction and seal failure by promoting wear of the valve seat and core, and by sticking to the sliding parts of the armature, etc. Install a suitable filter (strainer) immediately upstream from the valve. As a general rule, use 80 to 100 mesh. Caution 1.