EX500-GPN2_eng (It is recommended to ground with resistance of 100 ohms or less) M12 M12 10 14.9 Operation, Storage: 35 to 85%RH (No condensation) Operating humidity range : Seal cap is provided.
Resistance to ground should be 100 ohms or less. -14No.EX-OMV0023-A LED Indication and Settings LED indication LED Status Description OFF SI unit operating voltage is not supplied. POWERLINK communication has not been established.
Please keep this manual handy for future reference. 030 3 [m] Power supply for input and control is ON Green LED is ON Communication cable 050 5 [m] 100 10 [m] LED is OFF Communication error between GW unit has occurred COM Green LED is ON Communication between GW unit is normal LED is OFF Power supply for Solenoid valve is OFF PWR(V) L Green LED is ON Power supply for Solenoid valve is ON
When 1 digit = 1 kPa, the pressure is given with an increment of 1 kPa, e.g., 1, 2, 3, , 99, 100. Digit (Min. setting unit) E One of the switch output types, and means the operation in which a switch is turned on when pressure equal to the switch output set value or less is detected.
The time from when the flow is applied as a step input (when the flow rate changes from 0% to 100% instantaneously) until the analogue output (voltage) reaches 90% of the actual flow rate. Response time Ripple Indicates pulsation. T Temperature characteristic The amount of variation in the analogue output or display value when the ambient temperature is changed. -13No.
(with polarity protection) Power consumption 50 mA or less -50No.PF-OMN0005-E Model PFMV3 Enclosure IP40 Operating temp. range Operating: 0 to 50 oC; stored: -10 to 60 oC (no frezzing or condensation) Operating humidity range Operating and stored: 35 to 85% R.H.
(Note1) (Petroleum,Water-glycol, Emulsion,Phosphoric ester) Applicable model FH100-06 FH100-08 FH100-10 FH100-12 FH100-16 FH100-20 FH100-24 INOUT Port size (Rc) 3/4B 1B 1 1/4B 1 1/2B 2B 2 1/2B 3B Drain port size M162 Rated flow Paper 50 80 120 160 260 450 600 rate Micromesh 60 100 150 200 300 550 700 (L/min) Operating pressure 1.0MPa Operating temperature 80oC Nominal filtration 1.
W hite Blue COM +12V +12V Yellow COM n Brown +12V Red Built-in sensor power supply 12VDC, 60 mA Black .. Cable with shield 4-3 Noise countermeasures 1. Use SMC extension cable CE1-R** for wiring of MONOSASHI-KUN and CEU5. Follow the instructions below to prevent malfunction due to noise. 2. Keep signal wires away from the power cables in wiring. 3.
Do not use a cable longer than 100 m. Do not cut the lead wire between the sensor and amplifier. It may malfunction after connecting it again. Environment Pay attention to use the product in an atmosphere with accumulation of iron waste or close contact with magnetic substances.
Do not use a cable longer than 100 m. For long wire lengths, we recommend a ferrite core should be attached to both ends of the cable, to reduce noise. (2) Do not use a load which generates a surge voltage.
Polyurethane tube for piping 4 (TU0425BU-100) 2m.
Polyurethane tube for piping 4 (TU0425BU-100) 2m. Conversion cable 1pc. 4 2.
Resistance to ground should be 100 ohms or less. -15No.EX-OMP0005-I LED Indication and Settings LED indication LED LED Status Description Red ON Communication error The station number and baud rate settings have been changed during communication Red flashing L ERR OFF Communication is normal L RUN Green ON Communication is normal OFF Communication has terminated (time out error) PWR Green
Resistance to ground should be 100 ohms or less.
Resistance to ground should be 100 ohms or less. A. Single power supply used B. Dual power supplies used Fig. 6 -14No.EX-OMB0014-H Settings Display setting Display Meaning PW LED is ON when the communication power is ON Indicates whether the SI unit is communicating with the master station correctly. LED is ON when the SI unit is receiving normal data from the master station.
-1.3kPa Withstand pressure Note2) 100 kPa(Except with pressure gauge) Knob resolution 0.13kPa or less Atmospheric intake consumption Note3) 0.6L/min(ANR) or less Ambient and fluid temperature 5 to 60 VAC side tubing O.D 68 6810 1/45/163/8 SET side tubing O.D 1/45/16 Standard connections 135g(IRV10-C08) 250g(IRV20-C10) Weight (No accessories) Single sided connections 125g(IRV10A-C08) 250g
Supply voltage for sensor 24 VDC Max. supply current for sensor 0.2 A/1 point, 0.9 A/1 unit Current consumption 100 mA or less (inside of Input unit) Input resistance 5.6 k Rated input current 4 mA or less 17 V or more/2.5 mA or more 17 V or more/2.5 mA or more ON voltage/ON current (Between input terminal and (Between input terminal and 0 V for sensor) +24 V for sensor) 7 V or less/1 mA
Network length Communication speed [kbps] 9.6 19.2 45.45 93.75 187.5 Max. cable length [m] 1200 1000 Communication speed [kbps] 500 1500 3000 6000 12000 Max. cable length [m] 400 200 100 : Maximum cable length differs depending on the specifications of a cable. The above cable length is based on type A cable.
Free flow Controlled flow Applicable cylinder bore size (mm) Effective area (mm2) Effective area (mm2) Flow rate (/min (ANR)) Flow rate (/min (ANR)) Model Port size Weight (g) AS420-02 2,500 1/4 38 3,600 55 0.34 AS420-03 5,000 3/8 77 4,800 74 0.33 63, 80, 100, 125 AS420-04 6,600 1/2 100 6,700 102 0.32 AS500-06 10,100 3/4 154 8,100 123 140, 160, 180, 200 0.36 AS600-10 15,100 1 230 16,900 258
AC DC Auto switch model Lead wire length (m) 0.5 (Nil) Load voltage Indicator light Wiring (Output) Special function Type Electrical entry Pre-wire connector Applicable load 3 (L) 5 (Z) Perpendicular In-line IC circuit 3-wire A96V A96 5 V Reed switch Solid state switch Grommet (NPN equivalent) Yes Yes 100 V 24 V 12 V A93 M9N M9P M9B F9NW F9PW F9BW A93V M9NV M9PV M9BV F9NWV F9PWV F9BWV