Title not found stattons : l : 20 | 20 staitons Type /rc Nvv5z3-4o-@2g|5 Stations I asize of A, B port lils | 10.32 Nom.
The product can be used at an ambient temperature as low as 20C, but take measures to prevent the solidification or freezing of impurities, etc. 2. When using for water, etc. in a cold area, devise a means to prevent freezing, such as draining the water from pipelines after stopping supply and exhaust water for a pump or other device.
a function of particle size d [mm] Mass concentration Cp Pressure dew point Concentration of liquid water Cw Concentration of total oil 0.1 < d 0.5 0.5 < d 1.0 1.0 < d 5.0 [mg/m3] [C] [g/m3] [mg/m3] 0 As specified by the equipment user or supplier and more stringent than class 1 1 20 400 10 70 0.01 2 40 6000 100 40 0.1 3 90 1000 20 1 4 10 +3 5 5 10 +7 6 0
(Specify a rail longer than the standard length.) D3 Input block stations AS-i, 8 in/8 out, 31 slave modes, 2 power supply systems Nil 1 None 1 station For 20 stations D20 AS-i, 4 in/4 out, 31 slave modes, 2 power supply systems AS-i, 8 in/8 out, 31 slave modes, 1 power supply system Note) In case of D0, only DIN rail fittings are attached.
the same as those on pages 17, 18, 19 and 20.
(A combination of single and double solenoid valves as long as the maximum number of solenoids does not exceed 16.)
Note) Contact P/A when replacing seals.
equipment such as a voltmeter.
head screw 2 23 Cross recessed round head screw 2 22 Cross recessed round head screw 2 21 Holding block (B) 2 28 20 Holding block (A) 2 19 Magnet 1 27 20 18 Magnet lever 1 Including No.19 17 Switch block (B) 1 16 Switch block (A) 1 15 Cover (B) 1 Gap 14 Cover (A) 1 13 Hexagon nut 1 12 Joint 1 11 Hexagon socket head cap screw 2 10 Hexagon socket head cap screw 2 9 Hexagon socket head cap
Please note that the graph should only be used as a guide as there is a tolerance of about 10% in the clamp cylinder body.
A 1 2 150 165 42.7 76.3 45 65 40 60 35 40 80 80 ALBA90-10 ALBA90-20 1.17-24
In particular, avoid application of pressure above the specifications caused by a water hammer.
A model should be selected with a holding force of 10 to 20 times that of the component weight. If high accelleration, decelleration or impact forces are encountered during motion a further margin of safety should be considered.
System configuration Make sure to install a mist separator (Series AM) on the inlet side of the booster valve. Also install a cleaning device such as an air filter or a mist separator on the outlet side as necessary. Because the booster valve contains a sliding mechanism and the inner wall of the tank for the booster valve is untreated, dust flows out to the secondary side.
When a surge generating a load such as a relay or solenoid is directly driven, use a type of switch with a built-in surge absorbing element. 4. Since the type of fluid varies depending on the product, be sure to verify the specifications. The switches do not have an explosion proof rating. To prevent a possible fire hazard, do not use with flammable gases or fluids. 5.
or more for Air pressure lock-up Sol A, B & C accept direct-operated type or pilot operated type. As you find that Solenoid valve Sol A for lock releasing is independent, you can use a compact 3-way valve and mount it dkeclly io lock-po[i by means of a nipple so that you can get the time delay of locking as short as possible. Diagram 6.
or more for Air pressure lock-up Sol A, B & C accept direct-operated type or pilot operated type. As you find that Solenoid valve Sol A for lock releasing is independent, you can use a compact 3-way valve and mount it dkeclly io lock-po[i by means of a nipple so that you can get the time delay of locking as short as possible. Diagram 6.
Cylinder with Lock Series MNB Taper ring Steel ball P f R R High locking efficiency Improved locking efficiency, as well as stable locking and unlocking (unlocking pressure 0.25MPa. 0.05MPa compared to conventional P/A products) have been realized by arranging a large number of precision steel ball bearings in two circular rows.
When not using this product as a replacement for HRG/HRGC, this function is not needed.
Install a mist separator (Series AFM) as a preliminary filter on the inlet side of the micromist separator to prevent premature clogging. 2. Do not install on the inlet side of the dryer as this can cause premature clogging of the element. Drain M5 x 0.8 AFD30, 40 Maintenance Float type auto drain OUT IN N.C. N.O. Warning 1.