Please contact SMC regarding the bowl assembly supply for PSI and F unit specifications.
Deflection on A when load is applied on F. Table deflection when yawing moment is applied. Deflection on A when load is applied on F. Table deflection when roll moment is applied. Deflection on A when load is applied on F.
N T, F, N are order made specifications.
Panel mount adapter + Front protective cover ZS-27-D With M3 x 8 l (2 pcs.) 956 Voltage Monitor for PFMV5 Series PFMV3 Specifications Model Series PFMV3 Applicable sensor Series PFMV505(F), PFMV510(F), PFMV530(F) Displayable range 0.70 to 5.10 V: The voltage under 0.7 V is displayed as LLL and that of 5.1 V or more is displayed as HHH.
Gravity is applied. mg F l l mg Friction force is applied. Rotation shaft is vertical (up and down). 2 Ta = = t2 Ts = F l Gravity is applied in rotating direction.
---t;F=f=='Tjt IN Bracket (Option) N ...'---Ht-t---t-+-H I--i IN o I w c.
Piping Threads with Sealant Caution Mounting Caution AS-F AS-F 1. This product has a stopper for fully close in rotating direction. Excess torque may break the stopper. Table below shows the maximum allowable torque of the knob. 1. If the fitting is tightened with excessive torque, a large amount of sealant will seep out. Remove the excess sealant. TMH ASD 2.
OK OK NG OK OK 17 4-2 W (N) WeN) () V m/s) () Va (m/s) L (m) M (Nm) E (J) g (m/s) (9.8m/ ) (N) W1 (Nm) V=1.4Va MFL F (V=0.) 1 L <> W1.VaW10 M2F2L2 F2 M= WeL =5VaWL 3 2 L W2 M3F3L3 F3 an= F Fmax 3 L F W4 Fmax : () W Ek= W V 2g (V=0.
Writing step data method (1)Write 0 in RWwn [bit8-F]. (2)Write the motion profile (position, speed) in RWwn+1 to 8 Refer to "7.1 Step data" of the operation manual of the controller(LEC). (3)Write the step data number which is changed in RWwn [bit0-7]. (Setting data range is from 0 to 63.) (4)Write 1 in RWwn [bit8-F].
Is E or F: For pressure switch for vacuum ,lead wire with connector (Length 2m) for pressure switch for vacuum G When 1.
Note 7) Select F or H for (1) System/Body Type for the single unit model. -13No. ZK2-OM00201 (4) Wiring Note 8) Symbol Type L Individual wiring Note 9) F D-sub connector (25 pins) Note 10) P Flat ribbon cable connector (26 pins) Note 10) N No wiring (No valve) Note 8) Common wiring is available only solenoid valve wiring. Individual wiring is specified for vacuum switches and sensors.
CJP Rear trunnion Integrated clevis Boss-cut basic Basic Axial foot Front flange Rear flange Single clevis Double clevis Front trunnion T E BZ B L F G C D U CJ2 F Low friction direction Boss-cut front flange FZ CM2 Side at pressure When pressurized on head side Boss-cut front trunnion B Side at pressure When pressurized on rod side UZ C85 CG1 L 40 150 CM2Q F Standard MB C95 CDM2Q L F 40 C73
(mm) Fitting size D 3.2 4 Weight g A B C E F Model M-32R-2 M-04R-2 36 36.5 31 .5 32 0.9 0.7 0.8 2 x 1 .2 20.5 4 Component Parts Note Electroless nickel plated Electroless nickel plated Material Brass Brass PP No. 1 2 3 Description Sleeve Studded body Stem Applicable fitting size D Applicable tubing 3 2 1 C F D E B A 15-6-29 6 Miniature Tubing and Miniature Fittings Specific Product Precautions
C/F C/F 23 C/F C/F 12 AFW16100-N120FGM-E* 16,100 1) Specify filtration grade by replacing; *: 5 = 5m; 1 = 1m; A = 0.01 m; C = activated carbon Technical Notes Correction Factor Threaded & Flanged Operating pressure Correction factor 1.
Lateral load: FA=mAg NO mAm =2000.19.8 =196(N) YES Calculate lateral load F A FA=mAg (N) (g: gravitational acceleration : 9.8m/s2) F=776(N) at P=0.5(MPa) is found on Figure-2-1. 196776 Calculate allowable lateral load F at operating pressure P. For relationship between lateral load F and operating pressure P, refer to Figure-2-1 (P7).
220-01 220-01-F 220-02 220-02-F 320-03 (02) 320-03-F (02) 420-04 420-04-F 121F-M3 131F-M3 121F-M5 (U10, 32) 131F-M5 (U10, 32) 221F-01 231F-01 2211F-01-06 221F-02 231F-02 321F-03 (02) 331F-03 (02) 421F-04 431F-04 1000F 2000F 2050F 3000F 4000F 1001F 2001F 2051F 3001F 4001F 230F 330F 430F 530F 630F 330F 430F 530F 630F Manifold regulator 4-, 5-port solenoid valve VQ Directional control valves
Piston speed Caution The cylinder speed upper limit that retains the particle generation grade is 400 mm/s. Back matter 5 Clean series: Common Precautions 3 Be sure to read before handling. Refer to the main text for detailed precautions for every series.
B C D E F G H I J K L M N O P Symbol Model A ARM2500 ARM3000 6 17 44 56 42 126.5 58 45 17 21 38 42 29 48 68 33.5 7 21 54 68 55 153.5 70 53 23.5 27.5 48.5 55 35 59 85.5 42.5 Dimensions by the Number of Stations Manifold stations 10 Model Symbol 9 8 7 6 5 4 3 2 L1 454 412 370 328 286 244 202 160 118 ARM2500 L2 442 400 358 316 274 232 190 148 106 L3 420 378 336 294 252 210 168 126 84 L1 592
*sure dlsplay Accuracy J3% (lull span) Minimum unit [ i l P a : 0 . 0 1 . k a f / c m ' : 0 . 0 1 , b a r : 0 . 0 1 .