EXxx-OMV0017-D 1 s Available Set the sampling frequency of the analog input equipment.
speed mm/s Piston speed mm/s Piston speed mm/s 8-16-7 7 Series CY1F Vertical Actuation 1.
mm/s Piston speed mm/s Piston speed mm/s Piston speed mm/s Technical Data 1547 CY1F Series Precautions at Vertical Operation and Intermediate Stop Vertical Actuation 1.
to 1000 mm/s Basic cylinder Rubber bumper Cushion Guide unit Built-in shock absorbers (2 pcs.)
speed mm/s Piston speed mm/s Piston speed mm/s 8-16-7 7 Series CY1F Vertical Actuation 1.
S S S S F0 function setting F1 function setting F99 function setting [Measurement mode] Measurement mode is the condition where the flow is detected and displayed, and the switch function is operating. This is the basic mode; other modes should be selected for set-point changes and other function settings. Do not use the product for flammable fluid. Fire or explosion can result.
Configuration One thermo-chiller for one master. 2 2 R D R D 3 3 S D S D 5 5 S G S G Master This product Do not connect any wire to other PIN numbers. Fig. 3-12 Connection of RS-232C 3.3 Installation HRR Series 3-20 HRX-OM-X071 Chapter 3 Transport and Setting Up 3.4 Piping Piping port size Connect piping firmly.
(Distance: 0mm) If the current exceeds 16000 A, check the distance between them. -16No.D-#S-OML0002-B Dimensions : Mounting the white heat shrinking tube with only D-P3DWSE. -17No.D-#S-OML0002-B : Mounting the white heat shrinking tube with only D-P3DWASE. -18No.D-#S-OML0002-B Revision history A: Housing, thread and connector changed.
The kinetic energy of load can be found using the following formula. 20 10 5 V M M 2 V 2 100 300 1000 2000 500 Ek = Ek: Kinetic energy (J) M: Weight of load (kg) V: Piston speed (m/s) Maximum drive speed (mm/s) Example) Load limit at rod end when air cylinder 63 is actuated with max. actuating speed 500 mm/s. at a maximum drive speed of 500 mm/s.
Very low speed (7 to 50mm/s) specifications There is no sticking and slipping even at very low drive speeds of 7 to 50mm/s. Furthermore, there is no lurching at start up, allowing smooth drive through the entire stroke.
B DIN rail mounting bracket [-D] VVQ1000-57A for {F, L, M, P, S (EX500) kit} VVQC1000-57A-S for {S (EX250) kit} VVQC1000-57A-T for {T, S (EX126) kit} 17 SOL. A 5 Station 7 SOL. B 18 SOL. A 6 Station 8 SOL.
19 7 31 27 12 16.5 22.5 29 M5 x 0.8 NN R 5st 10st S 15st W Q 5st 10st Z Bore size (mm) 4 6 10 15 Q G C 15st K H 2 39.5 31.5 23.5 3 32 24 16 7 M8 x 1.0 Hose nipple A W F E S Z H Refer to page 38.
System (16 output points) SUNX Corp.: S-LINK System (8 output points) Fuji Electric Co.: T-LINK Mini System DeviceNet, CompoBus/D (OMRON Corp.)
OMRON Corp.: CompoBus/S System (16 output points) OMRON Corp.: CompoBus/S System (8 output points) Mitsubishi Electric Corp.: CC-LINK System Note 2) BB Note) Add 2 stations for serial unit mounting.
Supply pressure: 0.1 MPa (7 L/min (ANR) per nozzle) Installation height of sensor: 10 mm 3 Electrostatic potential [kV] 20 With sensor Ionizer 2 Without sensor Without sensor Discharge time [s] 15 1 With sensor L 0 10 1 Workpiece Without sensor 5 2 With sensor 3 0 500 1000 1500 2000 Installation distance L [mm] 1 2 3 4 Time [s] Run mode after static neutralization (electrostatic potential
Without Air Cushion Bore size (mm) Bore size (mm) S ZZ S ZZ In the case of w/o air cushion, it comes with rubber bumper.
DB S 1 pc. With auto switch/ Plate mounting n n pcs. DP Bearing type Auto switch M Slide bearing Nil Without auto switch For the applicable auto switch model, refer to the table below. Auto switches are shipped together, (but not assembled).