Mechanically Jointed Rodless Cylinder MY1H Series Linear Guide Type: ø25, ø32, ø40 Piping can be connected from 4 directions on the head cover. Allows on-site piping to suit the MY1B installation MY1H MY1H conditions. MY1B MY1M MY1C MY MY-S25 MY-S32 MY-S40 Applicable cylinder A 105 130 145 B 119 148 167 C 35 45 55 D 50 64 80 E 8 11.7 14.8 F 5 6 8.5 G 9.5 11 14 H 5.5 6.6 9 J M6 x 1 M8 x 1.25 M10 x 1.5 A B A B A B MY1H25 MY1H32 MY1H40 MY1 HT Side supports consist of a set of right and left supports.
To release residual pressure, select a model with a back flow mechanism.
Suction Verification High Vacuum Suction Workpiece 1 Workpiece 2 Workpiece n Max. A P_1 H_1 n_1 Formula for Obtaining the Set Value Min.
Switch operating position (ON) Hysteresis Switch reset position (OFF) Unit: mm Auto switch model Air gripper D-Y7 W N B D-Y59A B D-Y69A B D-Y7 WV N B D-Y7BA 0.8 0.6 0.7 0.5 MHL2-10Dl Note)Use a watchmakers screwdriver with a grip diameter of 5 to 6mm to tighten the auto switch set screw. Use a tightening torque of 0.05 to 0.1 Nm.
Gripping force N = 38 N A gripping force of 38 N satisfies the required gripping force of 29.4 N. Therefore, the selection of MHF2-12D is appropriate.
Gripping force N = 38 N A gripping force of 38 N satisfies the required gripping force of 29.4 N. Therefore, the selection of MHF2-12D is appropriate.
25.5 25.5 A 32.5 33 37 28 32.5 32.5 A 31.5 22.5 27 27 A 35.5 26.5 31 31 MKl20 MKl25 MKl32 MKl40 MKl50 MKl63 Auto Switch Mounting Bracket Part No.
20D1 A gripping force of 73 N is obtained from the intersection point of gripping point position R = 70 and a pressure 0.5 MPa.
0 20 40 60 80 100 Load N 0 20 40 60 80 100 Load N 0 50 100 150 200 250 Data 8-9-9 9 Series MXY Table Deflection Table deflection due to pitch moment load Displacement at A when load is applied F Table deflection due to yaw moment load Displacement at A when load is applied F Table deflection due to roll moment load Displacement at A when load is applied F A A F A F F L L L L dimension mm
Leakage voltage Particularly when using a resistor in parallel with a switching element and using a C-R element (surge voltage suppressor) to protect the switching element, take note that leakage current will flow through the resistor and C-R element, etc., creating a danger that the valve may not shut OFF.
Use a 3 wire switch if this specification will not be satisfied. Moreover, leakage current flow to the load will be n times larger when n auto switches are connected in parallel. 7. Do not use a load that generates surge voltage.
U side 1 2 3 4 5 D side VQ 6 barb fitting 3 (EXH) port VKF (18) 12 VQZ 7 3.5 5 5 3.2 3.5 VZ P = 7.2 12.8 n-3.2, 4 barb fitting 2 (OUT) port VS VFN Dimensions Formulas: L1 = n x 7.2 + 14.8, L2 = n x 7.2 + 18.4, n: Stations (maximum 20 stations) n L 12 101.2 104.8 19 151.6 155.2 2 29.2 32.8 3 36.4 40 4 43.6 47.2 5 50.8 54.4 6 58 61.6 7 65.2 68.8 8 72.4 76 9 79.6 83.2 10 86.8 90.4 11 94 97.6
(n pcs.) Close mounting
(A contact) N.O. (A contact) Number of auto switches N.O. (A contact) N.O. (A contact) 1 2 1 pc. 2 pcs. 6 6 pcs.
SRH SRP General line (low pressure) Locations requiring high pressure SRF Plant line (source pressure) ITV VBA 80 VBA (Two-stage pressure boost) 100 IC OUT 0.8 MPa ITVH VBA E 0.5 MPa ITVX IN 0.5 MPa Operating pressure: 0.8 MPa Bore size: 80 Output 4000 N Operating pressure: 0.5 MPa Bore size: 100 Output 3850 N PVQ VBA Equivalent output VY1 When charging a tank or the like from a source
Use a 3-wire switch if this specification cannot be satisfied. Moreover, leakage current flow to the load will be n times larger when n auto switches are connected in parallel. 7. Do not use a load that generates surge voltage.
) Max 10.5 (except connector) XLDV-40 to 80/With solenoid valve C M Fn (KF flange) Fd (K flange) C Port R (exhaust port) Solenoid valve for initial exhaust N Solenoid valve for main exhaust B 8.5 8.5 A G A Port P (pressure port) (mm) N M G Fn C B A Fd K Model XLDV-25 50 123 48 40 26 6.5 12 12 54.5 58.5 73.2 83.6 41 52 70 83 95 110 55 75 87 114 66 79 100 117 170 183 217 256 65 70 88 90
Since a large quantity of liquid will be pumped out, use a suitable throttle in the discharge port if problems occur. Note 3) With a low number of operating cycles, even a valve with a small Cv factor can be operated.