ZSE30/ISE30

When a surge generating load such as a relay or solenoid is directly driven, use a type of switch with a built-in surge absorbing element. 4. Since the type of applicable fluid varies depending on the product, be sure to verify the specifications. The switches do not have an explosion proof rating. To prevent a possible fire hazard, do not use with flammable gases or fluids. 5.

PFA/PFW

Never mount a switch in a place that will be used as a scaffold during piping work. Damage may occur if subjected to an excessive load. Especially when the switch supports piping, do not apply a load of 15Nm or more to the metal part of the switch. 11. Provide a section of straight pipe of at least 8 times the pipe diameter in the piping before and after a switch.



the External Pilot VEX1 3 3 B A M5 G 1.

Air Slide Table Long Stroke Type Series MXY ø6, ø8, ø12 1

use a watchmakers screwdriver with a handle diameter of about 5 to 6 mm.

REC

cable O.D.: 6.8 to 11.5) CE1 CE2 Proper Auto Switch Mounting Position D-H7 D-H7C D-H7NF D-H7W D-H7BAL D-C7 D-C80 D-C73C D-C80C ML2B D-G39 D-K39 D-A33/A34 D-A44 D-B5 D-B64 D-B59W D-G5NTL Bore size (mm) C J G5-S A B A B A B A B A B A B CV 20 56.0 31.5 50.0 25.5 55.0 30.5 51.5 27.0 53.0 28.5 49.5 25.0 25 MVGQ 56.0 31.5 50.0 25.5 55.0 30.5 51.5 27.0 53.0 28.5 49.5 25.0 32 59.5 36.5 53.5 30.5

SFOD-OMT0005CN

B-1 2 (L) A A-1 1 B B-2 6 1 1.5m B A-2 5 COM-A/COM B-3 3 3 3m COM-B/ A-3 4 5 5m Shield (3) Vcc B-4 12 GND A-4 13 A B-5 7 A A-5 6 B B-6 S 9 B A-6 8 3 (14.2) (2) 2 1 (8) (1) B1 A1 (14) (18) (17.7) 5 6 (3) 2 1 A6 B6 15 16 L (11) (30.7) 14.2 [820m] LE-CP(1) (2) * * A B-1 2 (L) A A-1 1 B B-2 6 8 8m * B A-2 5 COM-A/COM B-3 3 A 10m * COM-B/ A-3 4 B 15m * (3) Shield

Series KP/KPQ/KPG

Block off the heat with a cover, etc. 5. Do not use in locations where static electric charges will be a problem. Consult SMC regarding use in this kind of environment. 6. Do not use in locations where spatter occurs. There is a danger of spatter causing a fire.

Series KP/KPQ/KPG

Block off the heat with a cover, etc. 5. Do not use in locations where static electric charges will be a problem. Consult SMC regarding use in this kind of environment. 6. Do not use in locations where spatter occurs. There is a danger of spatter causing a fire.

Power Clamp Cylinder

Space at manual release Leave a space in order to release by hitting with a plastic hammer. 150 Min.

KP/KPQ/KPG

Block off the heat with a cover, etc. 5. Do not use in locations where static electric charges will be a problem. Consult SMC regarding use in this kind of environment. 6. Do not use in locations where spatter occurs. There is a danger of spatter causing a fire.

Safety Instructions

Rc 1/8 7 to 9 Rc 1/4 12 to 14 Rc 3/8 22 to 24 Rc 1/2 28 to 30 Rc 3/4 28 to 30 Rc 1 36 to 38 Rc 11/4 40 to 42 Rc 11/2 48 to 50 Rc 2 48 to 50 Reference How to tighten M5 threads on the fittings After tightening by hand, use a tightening tool to add about 1/6 turn more. But when using miniature fittings, after tightening by hand, use a tightening tool to add 1/4 turn more.

3 Port Solenoid Valve Series VQ100 1

When ordering a valve with a lead wire of 600 mm or longer, be sure to indicate the model number of the valve without connector and connector assembly. A-C ON Orange P A P A Orange OFF A R B-C ON (Reset) A R Green 4-12-4 5 Series VQ100 Precautions Be sure to read before handling. For Safety Instructions and Solenoid Valve Precautions, refer to page 4-18-2.

3 Port Solenoid Valve Metal Seal/Rubber Seal Body Ported VQZ100/200/300

port} (A) 2 N.C.

VQ

Passage Indicator light Single Indicator light Latching A-C ON (Set) Passage A-C ON Orange P A P A Orange OFF A R B-C ON (Reset) A R Green 2.9-4 Series VQ100 Caution Caution How to Use of Multi-connector (For plug-in manifold: For VV3Q11) How to Connect/Disconnect DIN Rail qConnecton/Disconnection of Plug Removing 1) Loosen the clamp screw of the end plate on both sides.

Compressed Air Preparation Filter

Unit: Nm Recommended Torque Connection thread 1/8 1/4 3/8 1/2 3/4 1 1 1/2 2 Torque 7 to 9 12 to 14 22 to 24 28 to 30 28 to 30 36 to 38 48 to 50 48 to 50 * After tightening by hand, use a tightening tool to tighten an additional 1/6 turn. 2. Select according to the maximum flow rate of the system. 2.

3-Position Rotary Table

Piping and Speed Conrol 1) A single 3-position pressure center solenoid valve or two 3-port solenoid valves are used. (Refer to Figure 1 or Figure 2.) 2) A meter-out-type speed controller is used for ports A and B and a meter-in speed controller is used for ports C and D.

Stainless Steel High Vacuum, Angle/In-line Valve, Angle type Series XM, In-line type Series XY

-16 XMC-25 XMC-40 XMC-50 XMC-63 XMC-80 40 50 65 70 88 90 26 28 36 38 45 56 P.C.D 27 P.C.D 58.7 P.C.D 92.1 XYC/In-line type C D G Fd C (K flange) B J H 45 E A Fn (KF flange) (mm) Model A 85 115 129 158 189 B 48 66 79 100 117 C 1 2 2 3 3 D 23.5 38 53 61 80 E 40 55 75 87 114 Fn 95 110 Fd 26 41 52 70 83 G 64 84 95 118 142 H J XYC-25 XYC-40 XYC-50 XYC-63 XYC-80 100.2 130 178 209 268 28 36 38

MLGC

Fine Lock Cylinder with Guide Series MLGC 20, 25, 32, 40 A linear transfer cylinder unit with a built-in locking mechanism and a guide rod integrated in a compact design.

How to Order Series ZM Vacuum Ejector With Valve and Switch For details about certified products conforming to international standards, visit us at www.smcworld.com. 1

in a manifold.

VHK

/2(A): Male thread 1(P): Male thread/2(A): Male thread 1(P): Male thread/2(A): One-touch Applicable tube O.D.