FGG-E For the replacement of the element, see Replacement of the element on page 6. Confirm cautions on page 2 and 3 for use. 6/8 FGX-OM-L010 5. Replacement of the element 1 Removal of the cover Retainer bracket Stop operation Close the valve in order of INLET, then, OUTLET.
[] 23 6/8 FGX-OM-L011 5 1 INLETOUTLET O (1)(2) (2) AL-25S(:NBR) AL-22S(:FKM) (1) 2 3 23 7/8 FGX-OM-L011 4 O O 1 2 (1) (2) 5 (a)(b) V [(c)] [(c)] O 1 V V V V O (a) V (b) V (c) 6 8/8 FGX-OM-L011 URL http://www.smcworld.com Akihabara UDX 15F, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021,JAPAN Phone: +81 3 5207 8249 Fax: +81 3 5298 5362 Specifications are subject to change without
How to order 6 4. Precautions for handling 7~8 5. Troubleshooting 9 6. Exploded View 10 7. Drawing 11 -1- Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Part name (1) Switching hand valve between Air servo cylinder circuit and fail-safe circuit (2) Check valve (3) Emergency air receiver (4) Lock-up valve (5) Air servo cylinder circuit supply valve (6) Fail-safe hand valve (Ex.
Mounting bracket, bolt, mounting frame, and tools are changed to non-magnetic materials. 6 The presence of a magnetic field source near the actuator (actuator, electric welding machine conductor, motor, magnet etc.) Malfunction due to magnetic field The Auto switch operates at multiple points.
Not match with load specification (2-wire type) < Load voltage (Switch internal voltage drop x n) n: Number of switch connected in serial Output stays OFF Display is normal 6 Wiring failure (Output line) (3-wire type) Connect condition (connector contact pin / crimp terminal). Correct wiring.
(Correct tensile force/increase bend radius) Lead wire disconnection 6 Presence of magnetic field generating source around the cylinder. (Cylinder, electric welding machine conductor, motor, magnet etc.) Use the shield between magnetic field generating source and cylinder. Keep the cylinder away from magnetic field generating source.
Mounting bracket, bolt, mounting frame, and tools are changed to non-magnetic materials. 6 The presence of a magnetic field source near the actuator (actuator, electric welding machine conductor, motor, magnet etc.) Malfunction due to magnetic field The Auto switch operates at multiple points.
Tighten with the cross recessed round head screw. (6) Mount the tube gasket 11 to the left cover 2 to mount to the body 1 .
Installation of driver 5 3.1 Automatic Installation 5 3.2 Manual Installation 6 4. ACT Controller Installation 10 4.1 Installation 10 4.2 Check of the Communication Port 10 4.3 Communication Setting 11 4.4 Functions of Each Mode 12 -1No.JXC-OMX0002 Controller Setting Kit 1.
Applicable fitting size (D) PSE53-R06 6 mm PSE53-R07 1/4 inch With sensor cable -14No.PS-OME0004-G Revision history A: For B: Change template. C: Complete revision. D: Modified errors in text. E: Measurement laws are added. F: Modified errors in text. [October 2017] G: Contents revised in several places.
Diaphragm breakage Replace the pump. 12 5) Leakage of fluids from pump connections. 6) Fluid leakage to the outside.
The recommended bend radius of the lead wire is 6 times the outside diameter of the sheath, or 33 times the outside diameter of the insulation material, whichever is larger. Replace the damaged lead wire with a new one. Wire correctly. Incorrect wiring can break the Pressure Sensor. Do not perform wiring while the power is on.
Pattern of the dial 8 6. Drawing 8 -1- Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Refer to Glossary of Terms on page 6 for detail of max. operating pressure differential and max. system pressure. 10 Select an option mark in page 7 by Applicable Fluids Check List for special fluids outside of the standard.
Setting at the time of shipment is 01. 1 9 0 9 0 1 2 2 8 8 7 3 7 3 6 4 6 4 5 5 8 - Setting the terminator Set PROFIBUS communication line terminator. With Terminator (at shipping) Without terminator Without terminator When the product is connected to the terminal of PROFIBUS communication line, be sure to set it to with terminator.
(Tightening torque 0.6 to 0.8Nm) Dipswitch ON 1 2 1 2 3 4 5 6 7 8 9 10 SW40 SW20 SW10 SW08 SW04 SW02 SW01 BS4 BS2 BS1 Hold/Clear Terminating resistor Setting at the time of shipment 1 2 1 2 3 4 5 6 7 8 9 10 Node address: 1 Baud rate: 10Mbps Hold/Clear: Clear Terminating resistor: disable Setting of node address Node address SW40 SW20 SW10 SW08 SW04 SW02 SW01 1 OFF OFF OFF OFF OFF OFF ON 2
MQQ P10 specifications MQM P12 specifications 6) Lack of cylinder thrust Increase the operating pressure or change the cylinder to the one with larger I.D.
6 o @6 The numbers are the same as the "Construction" of the MY3 series catalog (CAT.ES20-165). *BLUE links will lead to purchase pages. Call or email us at sales@smcpneumatics.com for request. Replacement Parts: Seal (Order them as required with by individual part numbers.) Description Material No.
3 Double acting Piston seal Rod seal CUJB4-PS NBR 4 6 8 10 CUJB4-PS CUJB6-PS CUJB8-PS CUJB10-PS Set of left nos. !1, !2, !3 and grease pack. CUJB6-PS Tube gasket CUJB8-PS CUJB10-PS Seal kit !1 to !3 comes as a set. Use the kit number for each bore size. Single acting, spring return CUJB4-S-PS 4 6 8 10 CUJB4-S-PS CUJB6-S-PS CUJB8-S-PS CUJB10-S-PS CUJB6-S-PS Set of left nos. !