Process Pump Do not continue idling except for priming the pump. 5 11. Condensation and freezing of the pilot port The air supply port of the air operated type can cool down quickly due to expansion of the supply air, and this may cause condensation on the piping and the condensation may freeze during operation in winter.
Names and functions of parts.11 6. How to use.11 7. Specification and how to order. 13 8. Discharge capability . 15 9. Troubleshooting. 17 10. Outer dimensions . 19 2 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Troubleshooting P.11 to 12 9. Construction and operating principle -P.13 10. Operating principle P.13 11. Sensor mounting (leakage sensor) P.14 1 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Looseness of bolts which fix the parts at each port (port, elbow fixing flange, port fixing flange, air port cover). 11 9.
Dimensions --11 7. Guaranteed term and guaranteed range 12 8. Parts replacement procedure 13 1 XL-OMP0001 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Warranty period and guaranteed range 11 6.Parts replacement procedure 12 1 XM-OMP0002-A Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
How to Order 11 2-2-1. MONOSASHI-KUN with BRAKE 11 2-2-2. Options 12 Chapter 3: Selection Flow Chart to Confirm Utility 1314 Chapter 4: Specifications 4-1. Cylinder Specifications 15 4-2. Sensor Specifications 15 4-3. Cylinder (Brake) Life 16 Chapter 5: Wiring 5-1. Connector Wiring Table 17 5-2. Wiring for Counter (Controller) 17 5-3. Wiring for Extension Cable 18 5-4.
Operation failure Incorrect wiring (1) Fuse blown out and/or lead wire broken (2) Incorrect contact at the contact and connection (3) Broken wire in the coil (4) Foreign matter caught in the spool valve (8) Swollen spool valve (5) Excessive oil supply (11) Coil has burned out.
Wire the communication line away from the noise source. 11 NS: Green LED is flashing Communication is not established. Check the following, and restart. Signal line is connected from PLC. The communication speed of PLC and SI unit is appropriate. Wire the communication line away from the noise source. NS: Red LED is flashing Communication timeout.
Specifications 10 to 11 4. Troubleshooting 11 5. Construction 12 -1- Metal One-touch Fittings Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Model Thread size Tightening torque SX3000 M2 0.17 Nm SX5000 M3 0.8 Nm SX7000 M4 1.4 Nm 11 SX3000-OMM0002-B -12-SX3000-OMM0002-B -13SX3000-OMM0002-B TROUBLESHOOTING Should any trouble be found during operation, trace the source of the trouble in the following order and take corrective action.
When these products are installed in equipment, provide adequate protection against noise by using noise filters. 11.
Fault No.11 Problem Possible cause Investigation method Countermeasures The inputs that are beyond the maximum point number do not operate. Check that the number of inputs has not exceeded the allowable number. The allowable number depends on the SI unit model. Inadequate total number of inputs from the Input block connected with the SI unit.
Description and Functions 9 5-1 LED indication 9 5-2 Terminal board 9 5-3 Address setting 10 5-4 Setting of Hold/Clear 11 6. Wiring 12 6-1 Communication wiring 12 6-2 Terminal resistance 13 6-3 Cable for communication line 13 6-4 Wiring to power supply 13 7. Troubleshooting 14 -1No.EX-OMF0012-B 1.
How to Use . 11 2-1. Procedures to operation . 11 3. Wiring . 12 3-1. AC adapter type/ IZG10-01, 02 . 12 3-2. Power supply cable type/ IZG10-03 . 12 4. Function . 13 4-1. Name of parts . 13 4-2. LED indication . 13 4-3. Mode setting switch . 14 4-4. Emitter maintenance (cleaning and replacement) . 15 4-5. Alarm function . 17 5. Performance . 18 5-1.
Exhaust Port Exhaust Residual pressure exhaust button (2.9) Port -4- Warning Warning Design/ Selection Design/ Selection (11) Push the residual pressure exhaust button all the way to the end position by using a tool. Push the residual pressure exhaust button all the way to the end position by using a tool having a tip diameter of 2.8 or below.
No.PS-OMM0005-J PRODUCT NAME Digital Pressure Switch MODEL / Series / Product Number ZSE10(F) ISE10 Table of Contents Safety Instructions 2 Model Indication and How to order 9 Summary of Product parts 11 Definition and terminology 12 Mounting and Installation 15 Installation 15 Piping 17 Wiring 18 Internal circuit and wiring example 19 Pressure Setting 20 Measurement mode 20 Function Setting
Recommended tightening torque: Modular AR/AW series 0.60.05 Nm ARM10/11 series 0.320.03 Nm Mount the main body of the Pressure switch. Insert the lock pin to the adapter to the end firmly. Supply pressure slowly, and ensure no air leaks.
Air Cylinder Speed controller Solenoid valve Regulator Air source Air filter Fig. 11 Basic Circuit 28 6.
And Adjust the offset voltage after supplying power. 23 Doc.No.IZ-OMK0015D (11) Timing chart Timing chart of normal operation Normal operation Reset operation Remarks Turn the power off to solve the problem, then supply power again. The error signal(OUT3) will be reset.