Process Pump Looseness of bolts which fix the parts at each port (port, elbow fixing flange, port fixing flange, air port cover). 11 9.
(Ensure there is no fiber or dust in the groove.) 12 XL-OMM0005-A Replacement procedure Division 1 Model High Vacuum Angle Valve Step 7 Step 8 Step 9 Step 10 Step 11 Screw for fixing valve S assembly Valve S seal assembly (mount it after checking it has one O-ring.)
Dimensions --11 7. Guaranteed term and guaranteed range 12 8. Parts replacement procedure 13 1 XL-OMP0001 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Warranty period and guaranteed range 11 6.Parts replacement procedure 12 1 XM-OMP0002-A Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Tightening torque of the hexagon socket head set screw (M4 x 0.7) shall be 1 to 1.2Nm. 21 - < Applicable Auto switches > Solid state switch D-P3DWA How to mount and move the auto switch Fig. 11 Mount the auto switch mounting bracket 2 to the tie rod.
External gripping 11 34 42 65 158 254 force D I.D. Internal 17 45 66 104 193 318 Note 1) Gripping force per finger Effective value (N) gripping force O.D. External gripping S 7.1 27 33 45 131 217 force I.D.
General requirements) ISO 10218-1992: Manipulating industrial robots -Safety JIS B 8370: JIS B 8361: JIS B 9960-1: 1 ) JIS B 8433-1993: *2) 1. 2. 3. 1. 2. 3. 4. 2 - / *3) 1 1.5 *3)1 1 () 3 - 1 1-1. 1)0.5MPa L = 20mm MHZ2-10* MHZ2-16* MHZ2-20* MHZ2-25* MHZ2-32* MHZ2-40* mm 10 16 20 25 32 40 D 0.20.7 0.10.7 MPa S 0.350.7 0.250.7 C oC -1060 mm 0.01 0.02 c.p.m. 180 60 D 11
Gripping point . 11 3-5. Dimensions . 12 3-5-1. JMHZ2-16D-X7400B-DTP-(N/P) . 12 3-5-2. JMHZ2-16D-X7400B-HC10DT-(N/P) . 13 3-5-3. JMHZ2-16D-X7400B-HC10-(N/P) . 14 3-6. Connector and pin layout . 15 3-6-1. JMHZ2-16D-X7400B-DTP-(N/P) . 15 3-6-2. JMHZ2-16D-X7400B-(HC10DT/HC10)-(N/P) . 16 3-7. Center of gravity . 17 4Product Specifications . 18 4-1.
Operation failure Incorrect wiring (1) Fuse blown out and/or lead wire broken (2) Incorrect contact at the contact and connection (3) Broken wire in the coil (4) Foreign matter caught in the spool valve (8) Swollen spool valve (5) Excessive oil supply (11) Coil has burned out.
Wire the communication line away from the noise source. 11 NS: Green LED is flashing Communication is not established. Check the following, and restart. Signal line is connected from PLC. The communication speed of PLC and SI unit is appropriate. Wire the communication line away from the noise source. NS: Red LED is flashing Communication timeout.
Specifications 10 to 11 4. Troubleshooting 11 5. Construction 12 -1- Metal One-touch Fittings Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Model Thread size Tightening torque SX3000 M2 0.17 Nm SX5000 M3 0.8 Nm SX7000 M4 1.4 Nm 11 SX3000-OMM0002-B -12-SX3000-OMM0002-B -13SX3000-OMM0002-B TROUBLESHOOTING Should any trouble be found during operation, trace the source of the trouble in the following order and take corrective action.
When these products are installed in equipment, provide adequate protection against noise by using noise filters. 11.
Fault No.11 Problem Possible cause Investigation method Countermeasures The inputs that are beyond the maximum point number do not operate. Check that the number of inputs has not exceeded the allowable number. The allowable number depends on the SI unit model. Inadequate total number of inputs from the Input block connected with the SI unit.
Description and Functions 9 5-1 LED indication 9 5-2 Terminal board 9 5-3 Address setting 10 5-4 Setting of Hold/Clear 11 6. Wiring 12 6-1 Communication wiring 12 6-2 Terminal resistance 13 6-3 Cable for communication line 13 6-4 Wiring to power supply 13 7. Troubleshooting 14 -1No.EX-OMF0012-B 1.
If the minimum setting unit is 1 L/min, the flow can be displayed in 1 L/min units, i.e. 10, 11, 12. Minimum setting unit N Normal condition (NOR) Reference condition for volumetric flow: 101.3 kPa, 0 C The flow measurement which is converted at normal atmospheric pressure conditions at 0 C.
Exhaust Port Exhaust Residual pressure exhaust button (2.9) Port -4- Warning Warning Design/ Selection Design/ Selection (11) Push the residual pressure exhaust button all the way to the end position by using a tool. Push the residual pressure exhaust button all the way to the end position by using a tool having a tip diameter of 2.8 or below.
No.PS-OMM0005-J PRODUCT NAME Digital Pressure Switch MODEL / Series / Product Number ZSE10(F) ISE10 Table of Contents Safety Instructions 2 Model Indication and How to order 9 Summary of Product parts 11 Definition and terminology 12 Mounting and Installation 15 Installation 15 Piping 17 Wiring 18 Internal circuit and wiring example 19 Pressure Setting 20 Measurement mode 20 Function Setting
Recommended tightening torque: Modular AR/AW series 0.60.05 Nm ARM10/11 series 0.320.03 Nm Mount the main body of the Pressure switch. Insert the lock pin to the adapter to the end firmly. Supply pressure slowly, and ensure no air leaks.
No.PS-OMM0003-J PRODUCT NAME Digital Pressure Switch MODEL / Series / Product Number ZSE80(F) ISE80(H) Table of Contents Safety Instructions 2 Model Indication and How to Order 9 Summary of Product parts 10 Definition and terminology 11 Mounting and Installation 14 Installation 14 Piping 16 Wiring 17 Pressure Setting 19 Measurement mode 19 Function Setting 21 Function selection mode 21 Default